9 October 2020 in InfoMat
The environmental challenges across the world step up the researcher's interest in different energy resources. Semitransparent perovskite solar cells (ST‐PSCs) could expedite generation of electricity as well as shows reassuring its significance in flexible electronics and building‐integrating photovoltaic as so forth in the next decade. It is highly recommended to endorse the relevance of semitransparent solar devices to fulfill the required level of energy even by using the roofs and windows of the buildings. In this review article, we pay more attention to recent developments of ST‐PSCs. Herein, a succinct overview of latest research about semitransparent solar cell technologies and ST‐PSCs is summarized. Moreover, the strategies to enhance the transparency of solar cells are described utilizing structure, transparent electrodes, perovskite film formation, tandem solar cells, color tuning, and human eye perception. Last but not least is that the serious concerns about stability of ST‐PSCs are vividly reviewed. image
28 April 2020 in ACS Applied Energy Materials
4 January 2022 in Nano Research
Perovskite solar cells (PSCs) have rapidly developed in the past few years, with a record efficiency exceeding 25%. However, the long-term stability of PSCs remains a challenge and limits their practical application. Many high-performance PSCs have an n-i-p device architecture employing 4-tert-butylpyridine (t-BP) and bis(trifluoromethane)sulfonimide lithium salt (Li-TFSI) as bi-dopants for the hole-transporting layer (HTL). However, the hygroscopicity of Li-TFSI and low boiling point of t-BP negatively impact the moisture stability of these PSC devices. Herein, we report the use of the fluorine-containing hydrophobic compound tris(pentafluorophenyl)phosphine (35FP) as a dopant for poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine] (PTAA). With better hydrophobicity and stability than undoped PTAA, a PSC device containing 35FP-doped PTAA demonstrated improved charge transport properties and reduced trap density, leading to a significant enhancement in performance. In addition, the long-term stability of a 35FP-doped PTAA PSC under air exposure without encapsulation was demonstrated, with 80% of the initial device efficiency maintained for 1,000 h. This work provides a new approach for the fabrication of efficient and stable PSCs to explore hydrophobic dopants as a substitute for hydrophilic Li-TFSI/t-BP.
15 August 2022 in Applied Physics Letters
Recently, it has been demonstrated that the use of SnO2 as the electron transport layer (ETL) of perovskite (PSK) solar cells (PSCs) yields high efficiency, which is comparable to that of the TiO2 layer with the same structure. At the same time, the SnO2-based PSCs show improved stability. Herein, the defects at the device interface are reduced and the efficiency of the planar PSCs is enhanced by improving the interface contact between the ETL and the perovskite (PSK) layer. As an essential amino acid, tyrosine (Tyr) is introduced into SnO2 to fill the oxygen vacancies in SnO2 films and improve the nucleation of PSK. From our analysis, it was found that the interface contact between the SnO2 ETL and the PSK layer was increased and the defects at the interface were reduced. In addition, it was demonstrated that the introduction of Tyr could effectively suppress the charge recombination and improve the electron extraction efficiency. As a result, a champion power conversion efficiency (PCE) of 22.17% was obtained from Tyr modified PSCs, owing to the enhanced PSK film quality and carrier extraction efficiency. On top of that, the Tyr-modified device still maintained 87% of the initial recorded PCE, which was stored in the ambient air (25 °C, 25% ± 5% RH) for 864 h without encapsulation.
23 October 2024 in Materials Horizons
The performance and stability of perovskite solar cells (PSCs) are critically influenced by the interfacial properties between the perovskite absorption layer and the electron transport layer (ETL). This study introduces a novel interfacial engineering approach using dipotassium 7-hydroxynaphthalene-1,3-disulfonate (K-NDS) as a multifunctional passivator to enhance both the SnO2 ETL and the perovskite absorber layer. The sulfonic acid groups (–SO3 −) in K-NDS effectively fill oxygen vacancies on the SnO2 surface, while the hydroxyl groups (–OH) passivate dangling bonds, improving the crystallinity of the perovskite film. Additionally, the diffusion of K+ from the SnO2 ETL into the perovskite layer optimizes energy level alignment, thereby enhancing charge carrier extraction and transport. This bifacial passivation strategy has significantly improved both the power conversion efficiency (PCE) and long-term stability of PSCs. The modified devices achieved a champion PCE of 23.00% and an open-circuit voltage (VOC) of 1.172 V. Furthermore, these devices maintained 75% of their initial PCE even after 1000 hours of storage under indoor environmental conditions. This work demonstrates the effectiveness of synergistic interfacial passivation in advancing the performance and durability of PSCs.
16 August 2021 in Applied Physics Letters
Transparent conductive electrodes are one of the important components of organic optoelectronic devices. Mg:Ag alloys have been widely used as a semi-transparent cathode for top-emitting organic light-emitting diodes (OLEDs) or transparent OLEDs (TrOLEDs) due to their high conductivity and relatively low work function. However, their low transmittance makes the light-extraction efficiency to be comparatively low. In this study, a highly transparent (84.6% in the visible light range), conductive, laminated cathode with the structure of ZnO/Mg:Ag/ZnO was fabricated via atomic layer deposition (ALD). ALD-deposited ZnO is used to protect the vulnerable ultrathin Mg:Ag-alloy layer, while preserving its low work function for the entire structure. In particular, the bottom ZnO layer is used as an ETL, which can provide reasonable energy alignment between the cathode layer and the emission layer and prevent metal particles from penetrating into the underlying organic layer. The top-emission OLED, which is prepared in this study by using the laminated cathode, showed an 85.8% increase in brightness, with a current density of 11.2 mA/cm3 at 4.0 V, which is an ultra-low voltage compared with devices made with Mg:Ag cathodes. In addition, the total luminance of TrOLEDs increases 34.4% compared with devices using Mg:Ag cathodes. Furthermore, the average transmittance of the device was still as high as 77.19% for visible light.