Zongxian Li

Zongxian Li

Auto-generated profile, based on publicly available information

Zongxian Li

Chinese Acad Sci, State Key Lab High Temp Gas Dynam, Inst Mech, Beijing 100190, Peoples R China

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2022 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
MLMeikuan Liu
Meikuan Liu
GHGuilai Han
Guilai Han
ZLZongxian Li
Zongxian Li
ZJZonglin Jiang
Zonglin Jiang
In this Letter, hypersonic boundary-layer transition was investigated on a large-scale cone with a height of 3 m and a half-cone angle of 7° at a zero angle of attack in the JF-12 hypersonic flight duplicate shock tunnel. For the same freestream unit Reynolds number, with the increase in the bluntness Reynolds number, the transition Reynolds number has a trend of first increasing and then decreasing, showing a “transition reversal” phenomenon. As the bluntness increased, the high/low-frequency instability waves in the boundary-layer were modulated, which caused the boundary-layer transition to be delayed and then advanced.

1 December 2023 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
ZLZongxian Li
Zongxian Li
MLMeikuan Liu
Meikuan Liu
GHGuilai Han
Guilai Han
DWDagao Wang
Dagao Wang
ZJZonglin Jiang
Zonglin Jiang
Air-blowing is one of the techniques for active flow control and thermal protection system of hypersonic vehicles. Introducing air into the hypersonic boundary layer alters the cross-sectional profile of the boundary layer, thereby influencing the boundary-layer transition. This study investigates the active air-blowing control effects on the hypersonic flat-plate boundary layer under various blowing mass flow rates and incoming Mach numbers by solving the Reynolds-averaged Navier–Stokes equations with the Langtry–Menter four-equation transitional shear stress transport model. The study examined alterations in the blowing boundary-layer profiles under two conditions: natural and bypass transition, induced by different blowing flow rates. Blowing significantly alters the sonic line and boundary-layer profile characteristics, triggering blowing oblique shock and causing alterations in the instability mechanisms of the two transition states. A higher Mach number intensifies compressibility effects, stabilizing the boundary layer and leading to an increase in the thickness of the blowing boundary layer and air film.

1 October 2024 in AIAA Journal
Verified
Journal Article
Closed access
ZLZongxian Li
Zongxian Li
MLMeikuan Liu
Meikuan Liu
GHGuilai Han
Guilai Han
DWDagao Wang
Dagao Wang
ZJZonglin Jiang
Zonglin Jiang

5 November 2024 in Computers & Fluids
Verified
Journal Article
Closed access
DWDagao Wang
Dagao Wang
GHGuilai Han
Guilai Han
MLMeikuan Liu
Meikuan Liu
ZLZongxian Li
Zongxian Li

29 May 2026 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
ZLZongxian Li
Zongxian Li
GHGuilai Han
Guilai Han

1 July 2024 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
DWDagao Wang
Dagao Wang
GHGuilai Han
Guilai Han
MLMeikuan Liu
Meikuan Liu
ZLZongxian Li
Zongxian Li
ZJZonglin Jiang
Zonglin Jiang
The incident shock attenuation phenomenon in shock tube has received widespread interest because of its inevitable influence on experimental gas properties. However, few studies have investigated the cascading effects of the resulting nonuniformity on shock reflection in shock tunnels before the nozzle. This paper describes a numerical study on the unsteady reflection of a decelerating incident shock driven by a decelerating piston, as a simplification of the complex nonideal factors. The initial decay and uniform parameter distributions are generated based on the non-inertial frame. The results indicate that the existence of the nonuniform area forces the reflected shock wave region to undergo a transition process of attenuation and then stability. The final values of the gas parameters in zone 5 will, therefore, deviate from those given by the traditional relation for an ideal shock tube, which are only dependent on the terminal shock Mach number. This affects the determination of the total temperature T5, which is difficult to measure directly. We discuss the reconstruction of the nonuniform region with the attenuation trajectory of the incident shock wave and find that there is no one-to-one correspondence between this trajectory and the resulting nonuniformity, which introduces additional uncertainties to the predictions. Thus, an analogy method is developed through the multilevel block building algorithm, allowing the total temperature T5 to be determined using the total pressure p5 considering the effect of nonuniformity. Further assessments verify the applicability of this method in cases with multidimensional and viscous interactions.