1 September 2017 in Journal of Natural Gas Science and Engineering
6 September 2013 in The Journal of Chemical Physics
We study the lower critical solution temperature (LCST) behavior of associating polymer brushes (i.e., poly(N-isopropylacrylamide)) using classical density functional theory. Without using any empirical or temperature-dependent parameters, we find the phase transition of polymer brushes from extended to collapsed structure with increasing temperature, indicating the LCST behavior of polymer brushes. The LCST behavior of associating polymer brushes is attributed to the interplay of hydrogen bonding interactions and Lennard-Jones attractions in the system. The effect of grafting density and molecular weight on the phase behavior of associating polymer brushes has been also investigated. We find no LCST behavior at low grafting density or molecular weight. Moreover, increasing grafting density decreases the LCST and swelling ratio of polymer brushes. Similarly, increasing molecular weight decreases the LCST but increases the swelling ratio. At very high grafting density, a partial collapsed structure appears near the LCST. Qualitatively consistent with experiments, our results provide insight into the molecular mechanism of LCST behavior of associating polymer brushes.
10 March 2017 in Scientific Reports
Understanding mechanisms of oil mobilization of tight matrix during CO2 injection is crucial for CO2 enhanced oil recovery (EOR) and sequestration engineering design. In this study exposure behavior between CO2 and tight rock of the Ordos Basin has been studied experimentally by using nuclear magnetic resonance transverse relaxation time (NMR T2) spectrum and magnetic resonance imaging (MRI) under the reservoir pressure and temperature. Quantitative analysis of recovery at the pore scale and visualization of oil mobilization are achieved. Effects of CO2 injection, exposure times and pressure on recovery performance have been investigated. The experimental results indicate that oil in all pores can be gradually mobilized to the surface of rock by CO2 injection. Oil mobilization in tight rock is time-consuming while oil on the surface of tight rock can be mobilized easily. CO2 injection can effectively mobilize oil in all pores of tight rock, especially big size pores. This understanding of process of matrix exposed to CO2 could support the CO2 EOR in tight reservoirs.
1 December 2011 in The Journal of Chemical Physics
We have performed classical density functional theory calculations to study the behavior of mixed polymer brushes tethered to a planar surface. We assume no lateral segregation of the polymer at the grafting density studied and consider an implicit solvent. For a binary mixture of short and long athermal polymer chains, the short chain is compressed while the long chain is stretched compared with corresponding pure polymer chains at the same grafting density, which is consistent with simulation. This results from configurational entropy effects. Furthermore, we add a mean-field interaction for each polymer brush to simulate their different response towards a solvent. The long chain is forced to dislike the solvent more than the short chain. Through the interplay between the solvent effects and configurational entropy effects, a switch of the polymer brush surface (or outer) layer is found with increasing chain length of the long chain. The transition chain length (long chain) increases with increasing the solvent selectivity, and decreases with increasing the grafting density of the long chain. These results can provide guidance for the design of smart materials based on mixed polymer brushes.
18 October 2012 in The Journal of Chemical Physics
The understanding of phase behavior of copolymer brushes is of fundamental importance for the design of smart materials. In this paper, we have performed classical density functional theory calculations to study diblock copolymer brushes (A-B) in an explicit solvent which prefers the A block to B block. With increasing B-block length (NB), we find a structural transition of the copolymer brush from mixed to collapsed, partial-exposed, and exposed structure, which is qualitatively consistent with experiments. The phase transitions are attributed to the interplay between entropic cost of folding copolymer brushes and enthalpic effect of contact between unlike components. In addition, we examine the effect of different parameters, such as grafting density (ρg), the bottom block length (NA), and the chain length of solvent (NS) on the solvent response of copolymer brushes. The transition chain length (NB) increases with decreasing ρg and NA, and a smaller solvent molecule makes the collapsed structure less stable due to its lower penetration cost. Our results provide the insight to phase behavior of copolymer brushes in selective solvents from a molecular view.
6 January 2017 in Journal of Applied Polymer Science