23 December 2016 in Scientific Reports
This article presents a structure-based modeling approach to optimize gas evolution at an electrolyte-flooded porous electrode. By providing hydrophobic islands as preferential nucleation sites on the surface of the electrode, it is possible to nucleate and grow bubbles outside of the pore space, facilitating their release into the electrolyte. Bubbles that grow at preferential nucleation sites act as a sink for dissolved gas produced in electrode reactions, effectively suctioning it from the electrolyte-filled pores. According to the model, high oversaturation is necessary to nucleate bubbles inside of the pores. The high oversaturation allows establishing large concentration gradients in the pores that drive a diffusion flux towards the preferential nucleation sites. This diffusion flux keeps the pores bubble-free, avoiding deactivation of the electrochemically active surface area of the electrode as well as mechanical stress that would otherwise lead to catalyst degradation. The transport regime of the dissolved gas, viz. diffusion control vs. transfer control at the liquid-gas interface, determines the bubble growth law.
15 February 2017 in ACS Applied Materials & Interfaces
4 March 2024 in Proceedings of the Canadian Engineering Education Association (CEEA)
Curricular design efforts benefit from system implementation for both development and ongoing improvement. A project-goal framework was selected to interconnect curricular efforts with artifacts of learning that represent graduate attributes across-curriculum. These artifacts are adjudicated in correlation with prepared rubrics to guide assessment in connection with set learning outcomes. While artifacts are a good metric to show learning outcomes in the eyes of the educator and accreditation boards, there are questions remaining if this perspective of learning is shared by the learners themselves, and if improvement in focus can be made by employing a LLM AI. Comparison of student surveys were correlated with machine-learning generated association of assignment rubrics to both course and program learning objectives. The results indicate that while both students and instructors share a similar perspective of what is going on in the classroom, these new AI tools could be used to improve the interconnection of learning goals to artifact requirements.
18 June 2024 in The Canadian Journal of Chemical Engineering
Before 2005, the term ‘teetering’ was relegated to the annuls of history as the term ‘fluidization’ was commonly utilized to describe gas–solids contacting processes. In his epochal article “Teetering”, examination of liquid‐fluidizing beds used for classification of minerals by size (sizing) or density (sorting), Norman Epstein described in detail the current understanding of particle segregation and mixing in liquid‐fluidized beds. Looking back in time, Dr. Epstein described the state‐of‐the‐art of modern uses of a traditional engineering technology and connected a historical framework to new opportunities for advancement. In the spirit of this re‐examination, an investigation of alternative ways of understanding this phenomenon are presented as inspired by the presentation of the contents of his ‘Teetering’ article at his 60th anniversary lecture to the Department of Chemical & Biological Engineering at the University of British Columbia. This article focuses on alternative concepts of construction for examination of teetering principles and further suggestions for avenues of research in this field and beyond.
15 October 2010 in ECS Transactions
Polybithiophene and polybithiophene-titania films were electropolymerized under galvanostatic conditions on carbon fibre paper substrates and tested under AM1.5G conditions in 0.5 mM H2SO4 in order to evaluate their catalytic performance, their photonic conversion efficiency, as well as their Faradaic photoelectrochemical performance for hydrogen generation. The electrochemical data indicates that the films were stable and showed promise as a viable photocathode material as they significantly reduced the cathodic overpotential needed to promote hydrogen generation up to a current density of 75 µAcm-2. The photonic efficiency was low and showed a maximum incoming photonic conversion efficiency (IPCE) at a current density of 240 µAcm-2. Substrate considerations such as sub-micron architectural variables should be further investigated alongside film thickness and nanoparticle composition to optimize the photonic and catalytic performance.
23 July 2018 in ECS Meeting Abstracts
Custom-designed electrochemical test systems allow for specific measurements to be generated for isolated variables in advanced materials testing. A well designed first-principle system can give insight into more complex interactions often found in real-world devices. Often, such isolated test systems utilize sub-systems that draw upon external reactants for sustained testing and exhaust reaction products as a result. Practical limitations on delivery of purified feed streams and mediation of exhaust require system operation that can fail unexpectedly, often as a result of failure of the system itself rather than of the materials under investigation. A novel system for testing of zinc-air fuel cell cathodes is presented as an example system that allows for total internal flows of reactant and product chemical flows. Such systems allow for cyclic purification and analysis of reaction products and establishment of a device in which the only output of the testing is heat and reliable data. Examination of test system control of state properties and elimination of suspected system contaminants highlight the benefits of the developed self-contained flow systems. Insight into general design characteristics for robust electrochemical test systems are developed in light of the limitations of the presented entropy machines.