This research investigates the high-temperature interactions between Ni–Fe–Co–Cr and Ni–Fe–Co–Cr–Ti–Al high-entropy alloys and industrial ceramic refractories with high corundum (Al 2 O 3 ) content (approximately 68–85 wt%) and SiO 2 as a secondary component. The primary objective is to assess wettability quantitatively and elucidate interfacial reactions that led to the formation of reaction layers, non-metallic inclusions, and surface contamination during melting and casting. Sessile-drop wetting experiments were conducted using a CLASIC high-temperature observation furnace/heating microscope, capable of operating at temperatures up to 1600°C. Contact angles were evaluated using axisymmetric drop shape analysis. To mitigate oxidation and isolate interactions between the refractory materials and metals, the experiments were conducted either in a vacuum or under a controlled overpressure of ultra-high-purity argon (≥ 99.9999%). Post-experimental analysis of the metal–ceramic interfaces was performed using scanning electron microscopy with EDX microanalysis, along with X-ray powder diffraction, to examine interfacial morphology, elemental distribution, and reaction products. The comprehensive wetting and post-mortem characterizations revealed a direct correlation between composition-dependent wettability and the development of interfacial reaction layers or phases. The findings provide essential guidelines for selecting corundum-rich crucibles and molds, as well as for establishing processing parameters that minimize interfacial degradation, ultimately enhancing casting yield and the reliability of components.
Biochar is an adsorbent material widely used to remove pollutants from water and wastewater. However, biochars have limited adsorption capacity for some pollutants and antibacterial properties, therefore enriched with functional groups from different compounds such as Zn-based ones. In that sense, this research aimed to impregnate Zn-containing NPs onto banana rachis-based biochar using the in situ wet method with zinc nitrate heptahydrate (ZnN) as precursor. The effect of different concentration of ZnN (0.5, 1 and 2 M) on impregnated biochar properties, adsorption capacity and antibacterial capacity were evaluated. Zn-containing compounds such as residual ZnN, Zn5(NO3)2(OH)8·2H2O (ZHN) and/or ZnO, mostly in the crystalline phase, were deposited on the biochar surface, incorporating surface functional groups such as NO3 and Zn-O, mainly. When the lowest initial precursor concentration was used, ZnN is predominant in the crystalline phase, while when the concentration of the precursor increased the main compound is ZHN. The incorporation of oxygenated surface functional groups increased Pb and brilliant blue adsorption capacities of the impregnated materials compared to the bare biochar. However, within the impregnated biochars, the increased precursor concentration causes a reduction in the adsorption capacity because of the obstruction of microporosity. The impregnation enhanced the antibacterial capacity of biochar against bacteria. The antibacterial capacity increases with the enlarged precursor concentration, and it is based on Zn2+ releasing. Impregnation of biochar with ZnN using mild post-impregnation temperature conditions improved the adsorption and antibacterial capacities. Nevertheless, further studies should be carried out with other kinds of pollutants.
Thermo-catalytic pyrolysis coupled with CO2 reforming offers a sustainable route for the simultaneous valorization of waste plastics and greenhouse gases. Herein, waste polypropylene (WPP) was pyrolyzed over HZSM-5, HBeta, and HY zeolite catalysts. The resulting gases were separated from pyrolysis oils and subsequently reformed with CO2 over Ni and Ni-Co-based catalysts. The zeolite framework topology significantly influenced the pyrolysis product distribution. In contrast to HBeta and HY—which generated aliphatic-rich pyrolysis oils with minor aromatic content and mixed olefin-paraffin gas streams—HZSM-5 selectively favored the formation of BTEX-dominant pyrolysis oil with lower aliphatic content, alongside a paraffin-rich pyrolysis gas. During CO2 reforming, variations in the initial composition of the pyrolysis gas feed mixtures— produced using different zeolite catalysts—did not significantly alter the resulting syngas yields or H2/CO ratios. Furthermore, the reforming catalyst 10Ni-MgAl2O4 exhibited similar coking behavior across all three feed compositions. Partial substitution of Ni with Co, particularly in 9.5Ni-0.5Co-MgAl2O4 enhanced reactant conversion, suppressed coke deposition, and increased syngas production. These findings demonstrate that combining tailored pyrolysis with an optimized bimetallic (Ni-Co) catalyst system effectively advances the simultaneous valorization of plastic waste and CO2.