29 June 2020 in Journal of Lightwave Technology
Multi-wavelength distributed feedback laser array based tunable semiconductor lasers have been widely used owing to their high mode stability and simple tuning scheme. Comparing with the in-parallel laser array, the in-series one can avoid a large power loss caused by the optical combiner. However, the single-mode stability of an in-series laser array is vulnerable to the reflections of other lasers. Here we experimentally demonstrated a tunable in-series laser array with high single-mode stability and high uniformity of wavelength spacing. To reduce the impact of such reflections, the Bragg gratings in different lasers were designed in phase, and the grating phase error was reduced by utilizing the reconstruction-equivalent-chirp technique. Besides, a three-section laser structure was applied in each laser to increase the priority of the dominant lasing mode. Four lasers with small wavelength-spacings of 2.5 nm were integrated in the in-series laser array. According to the measurement results of 40 in-series laser arrays (160 lasers), wavelength deviations of 90.6% lasers were within ±0.2 nm, average wavelength spacings of 97.5% of the measured laser arrays were deviated from the design within ±0.2 nm, and SMSRs of 96.3% lasers were above 45 dB. The output power was above 25 mW and the relative intensity noise was below -130 dB/Hz. Like the in-parallel laser array, the proposed laser array can be applied in either continuous wavelength tuning or fast channel switching. For the continuous wavelength tuning applications, the 10-nm tuning range was obtained with a temperature tuning range of less than 20 °C. For the fast channel switching applications, 4 channels with 2.5-nm spacing are available, and the switching time between two channels was less than 300 ns.
4 April 2018 in Optics Express
Photonic generation of linearly chirped microwave waveforms (LCMWs) using a monolithic integrated three-section laser is experimentally demonstrated in this work. All three sections of the laser cavity, including the front DFB section, phase section and rear DFB section, have the same active layer, which can avoid the butt-joint re-growth process. The gratings in both DFB sections are fabricated by the Reconstruction Equivalent Chirp technique, which can significantly decrease the difficulties in realizing precise grating structure. By adjusting the integrated three-section semiconductor laser to work in the period-one (P1) state and applying a sweeping signal to the front DFB section, the beating signal, i.e., an LCMW with a large time bandwidth product (TBWP), can be generated. In the current proof-of-concept experiment, an LCMW with a large TBWP up to 5.159 × 105 is generated, of which the bandwidth and the duration time are 6.7 GHz and 77 us respectively. The compressed pulse width is 150 ps. In addition, by adjusting the bias currents of the rear DFB section and front DFB section as well as the amplitude of the sweeping signals, LCMWs with tunable center frequency and tunable bandwidth can be achieved.
25 February 2019 in Optics Express
A novel approach to realizing an optoelectronic oscillator (OEO) based on an integrated multi-section (IMS) distributed feedback (DFB) laser is proposed and experimentally demonstrated. Our scheme adopts the method of direct modulation and a built-in microwave photonic filter (MPF), making the structure simpler and more flexible than an external modulator and electrical bandpass filter (EBPF). The IMS-DFB laser, which can overcome the drawbacks of using discrete lasers, is the key device in the scheme. Further, the two DFB sections, which are fabricated by Reconstruction Equivalent Chirp (REC) technique, are injected mutually. The SSB phase noise of the generated signal at the frequency of 20.3 GHz is −115.3 dBc/Hz@10kHz and −92.9 dBc/Hz@1kHz. The sidemode suppression ratio (SMSR) is 60.94 dB, which is a 40 dB improvement over a single loop. Furthermore, we demonstrate that the phase noise improves about 8 dB at the frequency offset of 1 kHz, when employing 13 km and 5.4 km fibers as the dual loop. The simple and compact structure, which consists of an IMS-DFB laser with high wavelength controlling accuracy and low process requirement, is a promising development for OEO integration.
24 October 2017 in Optics Express
A monolithic optical injection-locked (MOIL) DFB laser with large stable injection locking range is experimentally demonstrated using the side-mode injection locking technique. The low-frequency roll-off in the MOIL DFB laser is suppressed significantly. The relaxation oscillation frequency is measured to be 26.84 GHz and the intrinsic 3-dB response bandwidth is more than 30 GHz, which is about 20 GHz higher than that of the free running DFB laser. The nonlinear distortions, including the 1-dB compression point, second harmonic distortion (2HD) and third-order intermodulation distortion (IMD3), are also suppressed significantly. A simple radio-over-fiber system transmitting 40 Msymbol/s 32-QAM signal with 6 GHz carrier is achieved using the MOIL DFB laser. After 50 km transmission, the average error vector magnitude (EVM) of the whole link is 2.94% in injection locked state, while the EVM in free running DFB laser is 5.25% as a comparison. To our knowledge, this is the first time that the MOIL DFB laser is realized utilizing the side-mode injection locking method.
28 July 2015 in Optics Express
A frequency tunable optoelectronic oscillator based on a directly modulated distributed-feedback (DFB) semiconductor laser under optical injection is proposed and experimentally demonstrated. Through optical injection, the relaxation oscillation frequency of the DFB laser is enhanced and its high modulation efficiency can enable the loop oscillation with a RF threshold gain of less than 20 dB. The DFB laser is a commercial semiconductor laser with a package of 10 GHz, and its packaging limitation can be overcome by optical injection. In our scheme, neither a high-speed external modulator nor an electrical bandpass filter is required, making the system simple and low-cost. Microwave signals with a frequency tuning range from 5.98 to 15.22 GHz are generated by adjusting the injection ratio and frequency detuning between the master and slave lasers. The phase noise of the generated 9.75 GHz microwave signal is measured to be −104.8 dBc/Hz @ 10 kHz frequency offset.
3 May 2017 in Optics Express
The physical-layer security of a quantum-noise randomized cipher (QNRC) system is, for the first time, quantitatively evaluated with secrecy capacity employed as the performance metric. Considering quantum noise as a channel advantage for legitimate parties over eavesdroppers, the specific wire-tap models for both channels of the key and data are built with channel outputs yielded by quantum heterodyne measurement; the general expressions of secrecy capacities for both channels are derived, where the matching codes are proved to be uniformly distributed. The maximal achievable secrecy rate of the system is proposed, under which secrecy of both the key and data is guaranteed. The influences of various system parameters on secrecy capacities are assessed in detail. The results indicate that QNRC combined with proper channel codes is a promising framework of secure communication for long distance with high speed, which can be orders of magnitude higher than the perfect secrecy rates of other encryption systems. Even if the eavesdropper intercepts more signal power than the legitimate receiver, secure communication (up to Gb/s) can still be achievable. Moreover, the secrecy of running key is found to be the main constraint to the systemic maximal secrecy rate.