1 April 2009 in Journal of Applied Physics
Thermal diffusivity of polycrystalline tin-doped indium oxide (ITO) films with a thickness of 200 nm has been characterized quantitatively by subnanosecond laser pulse irradiation and thermoreflectance measurement. ITO films sandwiched by molybdenum (Mo) films were prepared on a fused silica substrate by dc magnetron sputtering using an oxide ceramic ITO target ( and ). The resistivity and carrier density of the ITO films ranged from to and from to , respectively. The thermal diffusivity of the ITO films was , depending on the electrical conductivity. The thermal conductivity carried by free electrons was estimated using the Wiedemann–Franz law. The phonon contribution to the heat transfer in ITO films with various resistivities was found to be almost constant , which was about twice that for amorphous indium zinc oxide films.
1 October 2012 in Earth and Planetary Science Letters
6 November 2001 in Measurement Science and Technology
A picosecond thermoreflectance measurement system has been developed in the National Metrology Institute of Japan in order to measure thermal diffusivities of metal thin films. A laser beam from a picosecond Ti-sapphire laser is focused onto the surface of a metal thin film with a spot size of 100 µm and absorbed within the skin depth of the order of 10 nm. Then, heat diffuses towards the opposite side of the thin film one-dimensionally, and the temperature of the heated face decreases over the time scale from ten picoseconds to several hundreds of picoseconds. This ultrafast temperature response is observed with a thermoreflectance method using probe picosecond pulses from the same source of the Ti-sapphire laser. Thermoreflectance signals for aluminium thin films with the thickness of 50 nm, 100 nm, and 500 nm sputtered on Pyrex 7740 glass substrates were observed under the front heating front detection (FF) configuration. We also developed a rear heating front detection (RF) type picosecond thermoreflectance measurement system. Thermoreflectance signals of molybdenum thin films and aluminium thin films with nominal thickness of 100 nm deposited on Pyrex 7740 glass substrates were observed at room temperature under RF configuration. Thermal energy transfer inside the molybdenum and aluminium thin films is dominated by the classical Fourier law. In-plane thermal diffusivities of the thin films are close to those of the bulk materials although out-of plane electrical resistivities measured by the four-probe method are larger than the resistivities of the bulk materials.
13 April 2015 in Japanese Journal of Applied Physics
Thermal conductivity of a 300-nm-thick VO 2 thin film and its temperature dependence across the metal–insulator phase transition ( T MIT ) were studied using a pulsed light heating thermoreflectance technique. The VO 2 and Mo/VO 2 /Mo films with a VO 2 thickness of 300 nm were prepared on quartz glass substrates: the former was used for the characterization of electrical properties, and the latter was used for the thermal conductivity measurement. The VO 2 films were deposited by reactive rf magnetron sputtering using a V 2 O 3 target and an Ar–O 2 mixture gas at 645 K. The VO 2 films consisted of single phase VO 2 as confirmed by X-ray diffraction and electron beam diffraction. With increased temperature, the electrical resistivity of the VO 2 film decreased abruptly from 6.3 × 10 −1 to 5.3 × 10 −4 Ω cm across the T MIT of around 325–340 K. The thermal conductivity of the VO 2 film increased from 3.6 to 5.4 W m −1 K −1 across the T MIT . This discontinuity and temperature dependence of thermal conductivity can be explained by the phonon heat conduction and the Wiedemann–Franz law.
1 July 2005 in Journal of Vacuum Science & Technology A
1 November 2005 in Review of Scientific Instruments
We have developed an apparatus to measure thermal effusivity distribution in solid materials with a high spatial resolution better than by the thermoreflectance technique and the periodic heating method. A metal film sputtered on the surface of a sample is periodically heated by a modulated laser beam. The temperature response is measured by using another thin laser beam as a thermoreflectance signal. The thermal effusivity of the sample is derived from the phase lag of the temperature response from the periodic heating. Measurements of a functionally graded material and a fiber composite material are presented as application examples of this thermal effusivity distribution measurement technique.