Doğan ŞİMŞEK

Doğan ŞİMŞEK

Auto-generated profile, based on publicly available information

Doğan ŞİMŞEK

National Defence University, Department of Automotive Technologies

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2019 in High Temperature Materials and Processes
Verified
Journal Article
Open access
PDF file
STSüleyman Tekeli
Süleyman Tekeli
ISIjlal Simsek
Ijlal Simsek
DSDogan Simsek
Dogan Simsek
DODursun Ozyurek
Dursun Ozyurek
In this study, the effect of solid solution temperature on microstructure and mechanical properties of the AA7075 alloy after T6 heat treatment was investigated. Following solid solution at five different temperatures for 2 hours, the AA7075 alloy was quenched and then artificially aged at 120 ∘ C for 24 hours. Hardness measurements, microstructure examinations (SEM+EDS, XRD) and tensile tests were carried out for the alloys. The results showed that the increased solid solution temperature led to formation of precipitates in the microstructures and thus caused higher hardness and tensile strength.

7 April 2016 in Arthritis Research & Therapy
Verified
Journal Article
Open access
PDF file
F(for the FMF Arthritis Vasculitis and Orphan Disease Research in Pediatric Rheumatology (FAVOR)
for the FMF Arthritis Vasculitis and Orphan Disease Research in Pediatric Rheumatology (FAVOR)
APAdem Polat
Adem Polat
CACengizhan Acikel
Cengizhan Acikel
BSBetul Sozeri
Betul Sozeri
IDIsmail Dursun
Ismail Dursun
EDErkan Demirkaya
Erkan Demirkaya
In this study, we examined the efficacy and safety of a once-daily dosage schema of colchicine compared with a twice-daily dosage schema in pediatric patients with familial Mediterranean fever (FMF). In this 24-week, multicenter, randomized controlled noninferiority trial, pediatric patients newly diagnosed with FMF carrying a homozygous or compound heterozygous mutation and not receiving any treatment were included. Patients were randomly assigned using a block randomization method to receive treatment with a once- or twice-daily dosage. Clinical and laboratory characteristics and medication side effects were recorded and compared between groups. The study was carried out in compliance with Good Clinical Practice and the Consolidated Standards for Reporting of Trials (CONSORT) statement. A total of 92 patients were selected, and 79 patients completed the study. There were 42 patients in the once-daily dosage group and 37 in the twice-daily dosage group. The results indicated that the once-daily dosage was not inferior to the twice-daily dosage regarding decrease in attack frequency and duration as well as improvement in clinical findings and Mor severity scores. Alterations in laboratory findings indicating inflammation, such as erythrocyte sedimentation rate, C-reactive protein, and serum amyloid A, were similar in both groups. The rates of drug side effects were similar between the once- and twice-daily dosage groups, implying comparable safety of colchicine, with the exception of diarrhea, which was slightly higher in the once-daily dosage group. Using colchicine with either a once- or twice-daily dosage provides similar clinical and laboratory improvements. Considering both efficacy and safety, colchicine can be prescribed with a once-daily dosage. ClinicalTrials.gov identifier NCT02602028 . Registered 5 November 2015.

19 May 2020 in Metals and Materials International
Verified
Journal Article
Closed access
PDF file
HSHaktan Sıralı
Haktan Sıralı
DŞDoğan Şimşek
Doğan Şimşek
DODursun Ozyurek
Dursun Ozyurek

15 May 2020 in Journal of Tribology
Verified
Journal Article
Closed access
PDF file
DSDogan Sımsek
Dogan Sımsek
DODursun Ozyurek
Dursun Ozyurek
In this study, high temperature wear performance of A356+Gr-ZrO2 aluminum matrix composites produced by the mechanochemical reaction method was investigated. After the aluminum composite powders were cold pressed (750MPa), the green compacts were sintered under 10−6 mbar vacuum for an hour at 550°C. Sintered AMCs have been characterized by Scanning Electron Microscopy (SEM), X-Ray Diffraction (XRD), hardness and density measurements. Wear tests were conducted in 2 different loads (10N and 30N), 5 different temperatures and 3 different sliding distances in the standard pin-on-disc type wear tester. Result showed that ZrO2 added to the matrix tends to cluster in grain boundaries. AMCs hardness and densities increased with increasing amount of reinforcement, and the highest hardness and density value was obtained with 12% ZrO2 added AMCs. Weight loss increased with increasing load and temperature and decreased with increasing amount of reinforcement in the matrix at all loads and temperatures.

21 November 2019 in Transactions of the Indian Institute of Metals
Verified
Journal Article
Closed access
PDF file
DSDogan Sımsek
Dogan Sımsek
NÇNIYAZI YILMAZ ÇOLAK
NIYAZI YILMAZ ÇOLAK
ISIjlal Sımsek
Ijlal Sımsek
DODursun Ozyurek
Dursun Ozyurek

15 April 2020 in International Advanced Researches and Engineering Journal
Verified
Journal Article
Open access
PDF file
IŞİjLal Şi̇mŞek
İjLal Şi̇mŞek
DŞDoğan ŞİMŞEK
Doğan ŞİMŞEK
DODursun Ozyurek
Dursun Ozyurek
Due to the many advantages it provides metal matrix composite materials, it is used as a publication in many industrial applications, especially in the automotive industry. Therefore, it is necessary to know the properties of these materials such as mechanical, tribological and corrosion. In this study, the effect of different sliding speeds was investigated on wear behavior of aluminum matrix composite materials produced by adding different amounts of ZrO2 by mechanical alloying method. 4 different amounts (3%, 6%, 9% and 12%) ZrO2 were added to the aluminum 2% graphite matrix. Composite powders mechanically alloyed for 60 minutes, were produced green compact samples by cold pressed with a pressure of 700 MPa. The green compacts produced were sintered for 2 hours at 600 °C. The produced aluminum composites were characterized by microstructure, density and hardness measurements. Wear tests were carried out on a block on-ring type wear testing device, under 20 N load and three different sliding speed (0.2 ms-1, 0.4 ms-1 and 0.6 ms-1) and three different sliding distances (53 m, 72 m and 94 m). As a result of the studies, hardness and density values increased as the amount of ZrO2 in the matrix increased. Wear test results showed that weight loss decreased with increasing amount of reinforcement in the matrix.