1 March 2015 in International Journal of Heat and Mass Transfer
1 February 2016 in Applied Physics Letters
A pool boiling phenomenon referred to as secondary boiling effects is discussed. Based on the experimental trends, a mechanism is proposed that identifies the parameters that lead to this phenomenon. Secondary boiling effects refer to a distinct decrease in the wall superheat temperature near the critical heat flux due to a significant increase in the heat transfer coefficient. Recent pool boiling heat transfer experiments using femtosecond laser processed Inconel, stainless steel, and copper multiscale surfaces consistently displayed secondary boiling effects, which were found to be a result of both temperature drop along the microstructures and nucleation characteristic length scales. The temperature drop is a function of microstructure height and thermal conductivity. An increased microstructure height and a decreased thermal conductivity result in a significant temperature drop along the microstructures. This temperature drop becomes more pronounced at higher heat fluxes and along with the right nucleation characteristic length scales results in a change of the boiling dynamics. Nucleation spreads from the bottom of the microstructure valleys to the top of the microstructures, resulting in a decreased surface superheat with an increasing heat flux. This decrease in the wall superheat at higher heat fluxes is reflected by a “hook back” of the traditional boiling curve and is thus referred to as secondary boiling effects. In addition, a boiling hysteresis during increasing and decreasing heat flux develops due to the secondary boiling effects. This hysteresis further validates the existence of secondary boiling effects.
26 March 2021 in Communications Materials
LKLarousse Khosravi Khorashad
Larousse Khosravi Khorashad
+4
It is very challenging to achieve near perfect absorption or emission that is both broadband and omnidirectional while utilizing a scalable fabrication process. Femtosecond laser surface processing is an emerging low-cost and large-scale manufacturing technique used to directly and permanently modify the surface properties of a material. The versatility of this technique to produce tailored surface properties has resulted in a rapidly growing number of applications. Here, we demonstrate near perfect, broadband, omnidirectional emissivity from aluminum surfaces by tuning the laser surface processing parameters including fluence, pulse count, and the ambient gas. Full-wave simulations and experimental results prove that the obtained increase in emissivity is mainly a result of two distinct features produced by femtosecond laser surface processing: the introduction of microscale surface features and the thick oxide layer. This technique leads to functionalized metallic surfaces that are ideal for emerging applications, such as passive radiative cooling and thermal management of spacecraft.
27 March 2019 in Journal of Heat Transfer
1 January 2018 in AIP Advances
The hydrodynamic mechanisms associated with the formation of femtosecond laser induced ripples on copper for two angles of incidence are reported. Laser pulse length used for this work is 35 fs. A revised two-temperature model is presented that comprises transient changes of optical characteristics during the irradiation with femtosecond pulses to model relaxation processes and thermal response in bulk copper. The theoretical model takes into account the fluid flow dynamics that result in ripple periods shorter than the wavelength of the surface plasmon polaritons. Theoretical and experimental results are reported for incident angles of 0° and 45° relative to the surface normal. There is agreement between the experimentally measured and the theoretically predicted ripple periodicity for 50 pulses at 0° incidence. By contrast, for 100 pulses at 0° incidence, and 50 and 100 pulses at 45° incidence, the experimentally measured ripples have a larger period than the one predicted by the model while the trends in period with increased incident angle, and increased fluence are in agreement between the experimental and the theoretical results.
1 December 2021 in Physics of Fluids
We present friction drag reduction in minichannel laminar flow past superhydrophobic metallic surfaces. Femtosecond laser surface processing (FLSP), a one-step scalable method, was used to create permanent microscale and nanoscale structures on 316 stainless steel plates. The resulting superhydrophilic plates were covered by tall (215 μm) or short (27 μm) structures. The FLSP plates were then transitioned to superhydrophobic by evaporative deposition of a fluorinated silane, a low surface energy coating. Using purified water, the friction factor was obtained by measuring pressure drop along a minichannel with a rectangular cross section for flow rates corresponding to Reynolds numbers from 45 to 250. The superhydrophobic FLSP plates with the tall or short microstructures were used on the bottom surface of the minichannel. Pressure drop reduction was observed when compared to a smooth unprocessed stainless steel surface at the same flow rate. Compared to the drag experienced by the smooth unprocessed surface, the superhydrophobic FLSP surfaces exhibited a drag reduction over the entire range of Reynolds numbers tested. The drag reduction was attributed to the slip velocity created by the presence of an air layer (plastron) between the water and the superhydrophobic surfaces. The superhydrophobic FLSP surface with the tall microstructures exhibited drag reduction that was almost constant at approximately 15% for the entire range of Reynolds numbers tested. The drag reduction for the surface with the short microstructures decreased monotonically with Reynolds number and ranged from about 31% at Reynolds number of 45 to about 25% at Reynolds number of 250.