Ali Ameri

Ali Ameri

Auto-generated profile, based on publicly available information

Ali Ameri

Aerospace Research Center, Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH 43235

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 December 2017 in Journal of Turbomachinery
Verified
Journal Article
Open access
PDF file
MHMohammad A. Hossain
Mohammad A. Hossain
RPRobin Prenter
Robin Prenter
RLRyan K. Lundgreen
Ryan K. Lundgreen
AAAli Ameri
Ali Ameri
JGJames Gregory
James Gregory
JBJeffrey P. Bons
Jeffrey P. Bons
A companion experimental and numerical study was conducted for the performance of a row of five sweeping jet (SJ) film cooling holes consisting of conventional curved fluidic oscillators with an aspect ratio (AR) of unity and a hole spacing of P/D = 8.5. Adiabatic film effectiveness (η), thermal field (θ), convective heat transfer coefficient (h), and discharge coefficient (CD) were measured at two different freestream turbulence levels (Tu = 0.4% and 10.1%) and four blowing ratios (M = 0.98, 1.97, 2.94, and 3.96) at a density ratio of 1.04 and hole Reynolds number of ReD = 2800. Adiabatic film effectiveness and thermal field data were also acquired for a baseline 777-shaped hole. The SJ film cooling hole showed significant improvement in cooling effectiveness in the lateral direction due to the sweeping action of the fluidic oscillator. An unsteady Reynolds-averaged Navier–Stokes (URANS) simulation was performed to evaluate the flow field at the exit of the hole. Time-resolved flow fields revealed two alternating streamwise vortices at all blowing ratios. The sense of rotation of these alternating vortices is opposite to the traditional counter-rotating vortex pair (CRVP) found in a “jet in crossflow” and serves to spread the film coolant laterally.

5 April 2021 in Journal of Turbomachinery
Verified
Journal Article
Closed access
PDF file
MHMohammad A. Hossain
Mohammad A. Hossain
AAAli Ameri
Ali Ameri
JGJames Gregory
James Gregory
JBJeffrey P. Bons
Jeffrey P. Bons

26 April 2016 in Journal of Turbomachinery
Verified
Journal Article
Closed access
PDF file
RPRobin Prenter
Robin Prenter
AAAli Ameri
Ali Ameri
JBJeffrey P. Bons
Jeffrey P. Bons

24 October 2013 in Journal of Turbomachinery
Verified
Journal Article
Closed access
PDF file
BCBrian Casaday
Brian Casaday
RPRobin Prenter
Robin Prenter
CBCarlos Bonilla
Carlos Bonilla
MLMichael Lawrence
Michael Lawrence
CCCarey Clum
Carey Clum
JBJeffrey P. Bons
Jeffrey P. Bons

11 March 2021 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Open access
PDF file
RBRobert J. Boyle
Robert J. Boyle
PGPritheesh Gnanaselvam
Pritheesh Gnanaselvam
APAnkur H. Parikh
Ankur H. Parikh
AAAli A. Ameri
Ali A. Ameri
JBJeffrey P. Bons
Jeffrey P. Bons
VNVinod K. Nagpal
Vinod K. Nagpal
The structural and aerodynamic performance of a low aspect ratio SiC/SiC ceramic matrix composite (CMC) high pressure turbine (HPT) blade was determined. The application was a NASA notional single aisle aircraft engine to be available in the N + 3, beyond 2030, time frame. The notional rpm was maintained, and to satisfy stress constraints, the annulus area was constrained. This led to a low span blade. For a given clearance, low span blade is likely to have improved efficiency when shrouded. The efficiency improvement due to shrouding was found to strongly depend on the axial gap between the shroud and casing. Axial gap, unlike clearance or reaction, is not a common parameter used to correlate the efficiency improvement due to shrouding. The zero clearance stage efficiency of the low aspect ratio turbine was 0.920. Structural analyses showed that the rotor blade could be shrouded without excessive stresses. The goal was to have blade stresses less than 100 MPa (14.5 ksi) for the unshrouded blade. Under some not very restrictive circumstances, such as blade stacking, a one-dimensional radial stress equation accurately predicted area averaged Von Mises stress at the blade hub. With appropriate stacking, radial and Von Mises stresses were similar.

1 December 2020 in Journal of Turbomachinery
Verified
Journal Article
Open access
PDF file
MHMohammad A. Hossain
Mohammad A. Hossain
AAAli Ameri
Ali Ameri
JGJames Gregory
James Gregory
JBJeffrey P. Bons
Jeffrey P. Bons
Experimental and numerical investigations were performed to study the effects of high blowing ratios and high freestream turbulence on sweeping jet film cooling. Experiments were conducted on a nozzle guide vane suction surface in a low-speed linear cascade at a range of blowing ratios of 0.5–3.5 and freestream turbulence of 0.6% and 14.3%. Infrared thermography was used to estimate the adiabatic cooling effectiveness. Thermal field and boundary layer measurements were conducted at a cross-plane at x/D = 12 downstream of the hole exit. Results were compared with a baseline 777-shaped hole and showed that the sweeping jet hole has improved cooling effectiveness at high blowing ratios (M > 1). The thermal field data revealed that the coolant separates from the surface at high blowing ratios for the 777-shaped hole while the coolant remains attached for the sweeping jet hole. Boundary layer measurements further confirmed that due to the sweeping motion of the jet, the effective jet momentum of the sweeping jet hole remains much lower than that of a 777-shaped hole. Thus, the coolant remains closer to the wall even at high blowing ratios. Large Eddy simulations (LES) were performed for both the sweeping jet and 777-shaped hole to evaluate the interaction between the coolant jet and the freestream in the near hole regions. Results showed that 777-shaped hole has a strong jetting at high blowing ratio that originates inside the hole breakout edges thus causing the jet to blow-off from the surface. In contrast, the sweeping jet does not show this behavior due to its internal geometry and flapping motion of the jet.