The transmission of SARS‐CoV‐2 coronavirus has led to the COVID‐19 pandemic. Nucleic acid testing while specific has limitations for mass surveillance. One alternative is the main protease (Mpro) due to its functional importance in mediating the viral life cycle. Here, we describe a combination of modular substrate and gold colloids to detect Mpro via visual readout. The strategy involves zwitterionic peptide that carries opposite charges at the C‐/N‐terminus to exploit the specific recognition by Mpro. Autolytic cleavage releases a positively charged moiety that assembles the nanoparticles with rapid color changes (t<10 min). We determine a limit of detection for Mpro in breath condensate matrices <10 nM. We further assayed ten COVID‐negative subjects and found no false‐positive result. In the light of simplicity, our test for viral protease is not limited to an equipped laboratory, but also is amenable to integrating as portable point‐of‐care devices including those on face‐coverings.
Gold nanorods (GNRs) have attracted great interest for photo-mediated biomedicines due to their tunable and high optical absorption, high photothermal conversion efficiency and facile surface modifiability. GNRs that have efficient absorption in second near-infrared (NIR-II) window hold further promise in bio-applications due to low background signal from tissue and deep tissue penetration. However, bare GNRs readily undergo shape deformation (termed as 'melting effect') during the laser illumination losing their unique localized surface plasmon resonance (LSPR) properties, which subsequently leads to PA signal attenuation and decreased photothermal efficiency. Polydopamine (PDA) is a robust synthetic melanin that has broad absorption and high photothermal conversion. Herein, we coated GNRs with PDA to prepare photothermally robust GNR@PDA hybrids for enhanced photo-mediated theranostic agents. Ultrasmall GNRs (SGNRs) and conventional large GNRs (LGNRs) that possess similar LSPR characteristics as well as GNR@PDA hybrids were compared side-by-side in terms of the size-dependent photoacoustic (PA) imaging, photothermal therapy (PTT), and structural stability. In vitro experiments further demonstrated that SGNR@PDA showed 95% ablation of SKOV3 ovarian cancer cells, which is significantly higher than that of LGNRs (66%) and SGNRs (74%). Collectively, our PDA coating strategy represents a rational design for enhanced PA imaging and efficient PTT via a nanoparticle, i.e., nanotheranostics.
This article presents an application of an active all-optical photoacoustic sensing system with four elements for steel rebar corrosion monitoring. The sensor utilized a photoacoustic mechanism of gold nanocomposites to generate 8 MHz broadband ultrasound pulses in 0.4 mm compact space. A nanosecond 532 nm pulsed laser and 400 μm multimode fiber were employed to incite an ultrasound reaction. The fiber Bragg gratings were used as distributed ultrasound detectors. Accelerated corrosion testing was applied to four sections of a single steel rebar with four different corrosion degrees. Our results demonstrated that the mass loss of steel rebar displayed an exponential growth with ultrasound frequency shifts. The sensitivity of the sensing system was such that 0.175 MHz central frequency reduction corresponded to 0.02 g mass loss of steel rebar corrosion. It was proved that the all-optical photoacoustic sensing system can actively evaluate the corrosion of steel rebar via ultrasound spectrum. This multipoint all-optical photoacoustic method is promising for embedment into a concrete structure for distributed corrosion monitoring.
This paper presents the design, fabrication, and characterization of a novel fiber optic ultrasonic sensing system based on the photoacoustic (PA) ultrasound generation principle and Fabry-Perot interferometer principle for high temperature monitoring applications. The velocity of a sound wave traveling in a medium is proportional to the medium’s temperature. The fiber optic ultrasonic sensing system was applied to measure the change of the velocity of sound. A fiber optic ultrasonic generator and a Fabry-Perot fiber sensor were used as the signal generator and receiver, respectively. A carbon black-polydimethylsiloxane (PDMS) material was utilized as the photoacoustic material for the fiber optic ultrasonic generator. Two tests were performed. The system verification test proves the ultrasound sensing capability. The high temperature test validates the high temperature measurement capability. The sensing system survived 700 °C. It successfully detects the ultrasonic signal and got the temperature measurements. The test results agreed with the reference sensor data. Two potential industry applications of fiber optic ultrasonic sensing system are, it could serve as an acoustic pyrometer for temperature field monitoring in an industrial combustion facility, and it could be used for exhaust gas temperature monitoring for a turbine engine.
Periodontitis remains a significant public health concern. According to the Office of Disease Prevention and Health Promotion, 37.4% of adults aged 45 to 74 years had moderate or severe periodontitis in 2013 to 2014.1 Periodontitis has been linked to diabetes,2 infective endocarditis,3 cardiovascular disease,4 respiratory disease,5 and mental illness.6 Periodontitis is a chronic inflammatory disease caused by subgingival bacteria that destroy the teeth’s supporting structures.7 Periodontitis can lead to gingival inflammation, gingival recession, bone mobility, and bone/tooth loss.8 The extent of periodontitis is measured to indicate the treatment and monitor the treatment response. Bone loss can be measured on radiographs,9 and mobility is measured via manual manipulation.10 The degree of inflammation is subjective and is based on the color of the gingiva and the frequency of bleeding on probing.11 Recession is the main characteristic of periodontitis and is associated with clinical attachment loss (CAL).12 CAL is assessed by measuring the gingival margin (GM) and the pocket depth. Oral health professionals generally use a periodontal probe such as a Williams probe to measure the pocket depth.13 However, periodontal probing can be affected by the probing force, the insertion point, and the probing angulation.14,15 Periodontal probing can also cause bleeding, is painful to the patient, and is time consuming for the provider.
Radiofrequency ablation (RFA) is a clinical technique which inactivates targeted biological tissues by heating to remove tumors or to cure diseases like atrial fibrillation. Temperature is a fundamental parameter for ablation dose control and treatment effect evaluation. This paper presents the design, fabrication and characterization of an all-optical fiber ultrasound temperature measurement probe. The novelty of this probe is to both generate and receive ultrasound optically through fibers. The ultrasound generation was achieved with a 425 μm multi-mode fiber based on photoacoustic (PA) principle and the receiving part applied a 125 μm single mode fiber with a Fabry–Pérot (FP) interferometer on its tip. The temperature was measured through detecting the time-of-flight (TOF) of the reflected ultrasound pulses. The probe’s feasibility of measuring temperature during ablation had been verified in vitro while excised bovine liver tissue was used as the ultrasound reflector.