Youqi Zhang

Youqi Zhang

Auto-generated profile, based on publicly available information

Youqi Zhang

Aalto University

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 December 2022 in Structures
Verified
Journal Article
Open access
Zhenkun LiZhenkun Li
Zhenkun Li
Weiwei LinWeiwei Lin
Weiwei Lin
YZYouqi Zhang
Youqi Zhang

4 February 2023 in Structural Health Monitoring
Verified
Journal Article
Open access
Zhenkun LiZhenkun Li
Zhenkun Li
Weiwei LinWeiwei Lin
Weiwei Lin
YZYouqi Zhang
Youqi Zhang
Bridge damage detection using vibration data has been confirmed as a promising approach. Compared to the traditional method that typically needs to install sensors or systems directly on bridges, the drive-by bridge damage detection method has gained increasing attention worldwide since it just needs one or a few sensors instrumented on the passing vehicle. Bridge frequencies extracted from the vehicle’s vibrations can be good references for damage detection. However, extant literature considered mainly low-frequency responses of the vehicle, while the high-frequency responses that also contained the bridge’s damage information were often ignored. To fill this gap, this paper developed a damage detection approach that utilized both low and high-frequency responses of the passing vehicle. Mel-frequency cepstral coefficients (MFCCs) and support vector machine (SVM) were employed to classify damage severity. Firstly, the vehicle’s frequency responses are utilized as input features to train SVM models to identify the bridge’s condition. Then, to reduce dimensions of inputs and improve training efficiency, frequency responses are projected from the Hertz scale into the Mel scale, and two means using MFCCs are used to feed different SVM models. A laboratory experiment with a U-shaped continuous beam and a model car was used to verify the effectiveness of the proposed method. Results showed that high-frequency responses contain much information about the bridge’s conditions, and using MFCCs could apparently improve computational efficiency. The errors of damage detection when a heavy car was employed were within 5%.

30 June 2023 in Structural Control and Health Monitoring
Verified
Journal Article
Open access
PDF file
Zhenkun LiZhenkun Li
Zhenkun Li
Weiwei LinWeiwei Lin
Weiwei Lin
YZYouqi Zhang
Youqi Zhang
Scanning the bridge’s frequencies from the passing vehicle’s vibration data has been frequently investigated recently. However, in previous studies, vehicles were typically simplified to quarter- or half-car models, and apparent disparity could be observed between the models and real vehicles. To make the vehicle model more practical, in this study, a 3D vehicle model is built to extract the bridge’s frequencies from vehicle vibrations. For the first time, equations for calculating the contact-point (CP) response of the 3D vehicle model are derived with tire damping. Furthermore, residual CP responses between front and rear wheels are utilized to eliminate the inverse effects of road roughness, making the bridge frequencies outstanding in the frequency domain. The robustness of the proposed method is tested under different influence factors, and two possible measurement errors are as follows: the sensor position and axle distance when applying the proposed method in engineering. Results show that the proposed method performs stably under the influence of different road roughness classes and tire damping. Bridge frequencies can be identified when the vehicle is travelling at a highway speed (108 km/h in this study). Environmental noises can submerge the bridge’s high-order frequencies but have little influence on the low-frequency range. High bridge damping will restrain the transmission of bridge vibration to the vehicle, making high-order bridge frequencies less visible. In addition, the errors introduced by a vehicle body sensor position can be eliminated when calculating the CP responses for tires, thus will not influence bridge frequency identification. To avoid possible errors induced by manual measurement of the axle distance, a novel cross-correlation function-based method is employed, which is verified effective and practical for calculating residual CP responses.

26 July 2023 in Mechanical Systems and Signal Processing
Verified
Journal Article
Open access
YZYouqi Zhang
Youqi Zhang
Zhenkun LiZhenkun Li
Zhenkun Li
RHRui Hao
Rui Hao
Weiwei LinWeiwei Lin
Weiwei Lin
LLLingfang Li
Lingfang Li
DSDi Su
Di Su

4 May 2023 in Structures
Verified
Journal Article
Open access
YZYouqi Zhang
Youqi Zhang
YMYasunori Miyamori
Yasunori Miyamori
TKTakanori Kadota
Takanori Kadota
TSTakehiko Saito
Takehiko Saito

7 July 2022 in SSRN Electronic Journal
Verified
Preprint
Open access
PDF file
YZYouqi Zhang
Youqi Zhang
Zhenkun LiZhenkun Li
Zhenkun Li
RHRui Hao
Rui Hao
Weiwei LinWeiwei Lin
Weiwei Lin
LLLingfang Li
Lingfang Li
DSDi Su
Di Su
Dynamic responses of structures simulated by finite element (FE) analysis can provide rich information for many downstream tasks, e.g., analysis of structural behaviors, design optimization, data-driven identification tasks, etc. The fidelity of simulated time-series data has a crucial effect on the results of those downstream tasks. Insufficient fidelity of simulation data can cause a typical problem: methods work perfectly on simulation data but are not effective on the actual structures. Meanwhile, owing to the successful adoption of Deep Learning (DL) in the engineering field, the demand for high-fidelity simulation data has greatly increased. FE model updating can partially address this problem. However, the time-series data generated by an updated FE model may still not satisfy the quality requirements of the downstream tasks. The simulated time-series data with higher fidelity are needed to further benefit the downstream tasks. Therefore, we proposed a method to synthesize realistic time-series data using finite element simulation and space projection. Two models, including a Dense Neural Network (DNN) and a Dilated Causal Convolutional Neural Network (DCCNN), were designed for realizing the space projection. Vibration experiments were conducted on an I-shaped steel beam to validate the proposed method. In addition to a case with sufficient training data, a few-short learning case is also investigated. The quality of the synthetic data is quantitively analyzed. Furthermore, the effects of sensor location and impact location on the quality of synthetic data are also discussed. Overall, the high quality of the synthetic time-series data generated by the proposed method is fully demonstrated.