Polymers are frequently used as contact materials in industrial applications that exploit the triboelectric effect. The aim of this paper is to investigate, with the help of 3D printing manufacturing technologies, how tribocharging of polymers is affected by their surface morphology. The experiments were performed using a linear tribometer to create the electric charge through friction between two samples. To highlight the correlation of surface texture with the level of triboelectric charge, the Polylactic acid (PLA) samples were manufactured with three different surface geometries, referred to as “lines”, “zigzag” and “waves”. The first series of experiments consisted in charging the surface of the PLA samples with the tribocharging bench for 20 and 40 cycles, with an Aluminum bar. The cartography of the electric potential at the surface was then performed, using a 2D mapping system to entrain the capacitive probe of an electrostatic voltmeter. In the second series of experiments, after tribocharging, the PLA samples were placed under the probe of the electrostatic voltmeter for 10 min to determine the surface potential decay (SPD) curve. The range of surface potential values was smaller for the “lines”-textured samples than for the other two, pointing out that the geometry of the texture significantly influences the outcome of the triboelectric charging. When comparing the SPD curves of the three textures for 20 cycles, it can be noted that ones for PLA with “lines” and “zigzags” are almost the same, but different from those of “waves”-type samples.
La décharge corona est largement utilisée non seulement pour modifier les caractéristiques physiques des surfaces des matériaux diélectriques, mais aussi comme technique de charge pour les mélanges granulaires en vue de leur séparation électrostatique. L’uniformité de la charge électrique déposée à la surface des matériaux isolants est un indice de performance majeur pour toute électrode corona. L’objectif de cette thèse a été d’explorer les limites des techniques de charge corona, et plus particulièrement l’uniformité de charge atteignable lors de l’utilisation d’électrodes corona multi-pointes, compte tenu de leur utilisation possible pour le traitement de surface des plaques diélectriques ou pour la séparation électrostatique de mélanges granulaires. L’utilisation d’un voltmètre électrostatique sans contact pour mesurer le potentiel électrique de surface après l’exposition à la décharge corona s’est avérée être une méthode pratique pour étudier la distribution et l’évolution de la quantité de charge déposée sur les matériaux isolants. Une étude « statique » réalisée avec des plaques de PVC au repos et soumises à l’action de la décharge corona générée par des électrodes corona multi-pointes a permis d’évaluer l’effet de chaque facteur : la tension appliquée, la hauteur des pointes au-dessus de la surface du diélectrique, et le temps d’exposition. Une étude « dynamique », dans laquelle les échantillons étaient en mouvement relatif par rapport aux électrodes de type multi-pointes, a permis de quantifier ces effets dans des conditions plus proches de celles qui devraient être rencontrées dans les applications industrielles. Ce travail a montré que la non-uniformité de la charge corona peut être réduite à moins de 5% de la valeur moyenne en choisissant des valeurs appropriées de la distance inter-électrodes et de la hauteur des extrémités des électrodes au-dessus de la surface exposée à la décharge corona.
23 December 2025 in IEEE Transactions on Industry Applications
Dielectric barrier discharges (DBD) are known to change the surface morphology, the surface chemical composition, and the triboelectric properties of the treated polymers. The work presented in this paper was aimed at studying the effect of long-term exposure of high-levels of ambient humidity on the triboelectric charging of DBD treated granular plastics. The experiments were carried out on four types of polymers, ABS, PP, PE and PS, with an average particle size between 4 mm and 6 mm. To study the effects of relative humidity of ambient air, the granules were stored for 72 h in a climatic chamber, disposing of simultaneous humidity and temperature control. The relative humidity was regulated at 82% ± 4%, for a temperature of 19°C ± 1°C. The water content of “humid” granules was measured with a thermal-balance and compared with that of “normal” granules, kept at ambient humidity (46% to 52%), at a temperature of 18°C ± 1°C. The “humid” and “normal” granules were successively exposed to a dielectric barrier discharge (DBD) for 60 s in a custom-designed reactor then charged by triboelectric effect in a multi-cylinder triboelectric device. As expected, the DBD treatment modified the triboelectric behavior of each polymer. The experiments showed that the charge/mass effect of this treatment is different on “humid” and “normal” particles. The study points out the importance of providing appropriate storage conditions (i.e., humidity levels lower than 70%) for the plastic wastes processed by tribo-electrostatic techniques.
20 March 2026 in IEEE Transactions on Industry Applications
The aim of this paper is to evaluate the effect of dielectric barrier discharge (DBD) plasma treatment on the tribo-electrostatic separation of brominated and non-brominated polymers contained in granular plastic wastes. The experiments were carried out on mixtures consisting of equal quantities of mm-size brominated and non-brominated polyethylene (PE) particles. Two triboelectric charging devices were used: a rotating multi-cylinder tribocharger, consisting of an assembly of six cylinders made of polyvinyl chloride (PVC), and a vibrating tribocharger (a container made of acrylonitrile butadiene styrene (ABS) and fixed on a vibrating table). The selective sorting of the granular mixtures was carried out using a roll-type electrostatic separator. Exposing the plastic mixture to a DBD plasma was used to increase the triboelectric charge of the particles and improve the efficiency of the tribo-electrostatic separation. The best results were obtained with the vibrating tribocharger: the recovery of almost 90% of the non-brominated PE particles in a product containing less than 1% of bromine.