30 July 2024 in Automobile Transport
Problem. From the analysis of the technical literature, it was established that among the trenchless technologies for laying underground engineering communications and service pipelines, the technology with the possibility of forming a horizontally directed communication cavity in the soil using soil-piercing installations of static action is the most common. Goal. This method consists in forcefully pressing a soil-piercing working body, which has the form of a conical-cylindrical projectile, into the soil. At the same time, the well is formed by radial extrusion of the soil around the formed well. However, the use of such equipment does not provide high accuracy, which limits its practical application within 20 m. It is not sufficient for modern requirements of creating transitions during the laying of communications. Methodology. One of the ways to improve the efficiency of laying underground networks is to extend this method over a longer distance by correcting the trajectory of the working body. This is achieved by using a soil-piercing head with an asymmetric tip. Due to this, in addition to the axial resistance of the soil, a transverse component force appears, which deflects the head during its advancement in the soil. The question of determining the angle of displacement of such a tip is important in terms of the process control. Results. In the paper, a calculated dependence is proposed for determining the rational value of the angle of inclination of an asymmetric tip working surface, which is a flat plane cut at the angle of a cylinder. An analysis of the dependence of the angle of the working surface inclination on the physical and mechanical properties of the soil is also given. Originality. It was determined that the maximum angle of inclination of the frontal surface is determined by the conditions of soil descent from it. Its maximum value, for example when working in loam, should not exceed 55o-67o for a tip made of steel. Practical value. The obtained calculated dependence can be useful for determining the angle of inclination of the flat frontal surface of the tip of the soil piercing working tool for controlled static soil piercing at the stage of designing networks and choosing an effective method for drilling a well under roads or other obstacles.
26 April 2023 in Transfer of innovative technologies
Modern requirements for the laying of underground communications consist of a combination of high construction rates with low energy consumption. The highest rate of laying linear objects is ensured by knife-type cable and pipe-layers, which are designed for their trenchless burial - this is when a narrow slot is cut in the soil, through which a cable or pipeline is launched. A feature of this process is the need to use large traction forces, which are determined by the resistance forces of the soil when cutting it. Accordingly, the cutting resistance of the soil depends on the dimensions of the width and depth of the gap and the physical and mechanical properties of the soil. Finding ways to reduce forces for deep cutting of soils is an important problem. One of the ways to improve the efficiency of trenchless laying machines is to equip them with vibrating knives. It is known that when the knife oscillates in the vertical direction, it leads, depending on the soil and the speed of movement, to a 30…60% decrease in traction resistance. But the use of more complex vibration movements of the knives allows reducing the traction resistance during deep cutting of soils by 70…90%. It is well-known that various designs of mechanical drive are used to implement the process of vibration of knives. These are complex devices that, together with the entire machine, require calculations. Therefore, studying the forced vibration of the knives of pipe deepeners is an urgent task, which is aimed at reducing the energy consumption of the process of soil deep cutting and improving the overall performance of knife machines for trenchless laying of underground utilities. To achieve the goal, the paper considered possible variants of the vibration oscillation of the knives and provided calculation dependencies for determining the resistance of soil cutting by active knives; also the dependence for determining the maximum average drive power of a centralized unbalanced vibrator was given. At the same time, the dimensions of the gap obtained, the physical and mechanical properties of the soil and the technical characteristics of the vibrator were taken into account.The obtained recommendations can be used when designing trenchless laying machines using vibrating knives.
2 February 2024 in APPLIED GEOMETRY AND ENGINEERING GRAPHICS
The technology of manufacturing parts from sheet steel is an important industry that provides the production of various products ranging from boxes to cars and construction equipment. However, the process of developing or modeling individual parts and assemblies as a whole precedes the manufacture of parts. To ensure the production of quality sheet steel products, it is necessary to include manufacturing technological aspects in the model at the development stage. Therefore, teaching and studying this topic should be combined with revealing the possibilities of CAD systems and manufacturing technologies. The work presents the technology of manufacturing parts from sheet steel, which is based on the most common equipment, namely laser cutting machines and coordinate-punch presses, which are used to obtain a layout of a part from a metal sheet. Vertical-bending presses and segmental bending machines, which bend the workpiece (layout) and give the final shape of the part. The necessary parameter for setting the sheet metal file is indicated, which can be expressed by the K-factor coefficient, and for educational purposes, it is recommended to accept it equal to K=0.44. Recommendations are given on the use of the most appropriate equipment and tool to implement a specific task. A table is provided with the most commonly used tool for gear cutting machines. The minimum possible technologically justified elements of the sheet metal part, which must be provided to implement the bending process at the design stage, are indicated. The advantages and disadvantages of each of the sheet metal processing methods are mentioned in projection onto the corresponding equipment, as well as cases in which it is rational to use this equipment. The most common formats of sheet steel are mentioned, which should be oriented when designing parts with the calculation of placing the layout of the part on them.