R. Muñoz-Arroyo

R. Muñoz-Arroyo

Auto-generated profile, based on publicly available information

R. Muñoz-Arroyo

Corporación Mexicana de Investigación en Materiales (COMIMSA), Saltillo, México

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2017 in Vacuum
Verified
Journal Article
Closed access
JAJ.L. Acevedo-Dávila
J.L. Acevedo-Dávila
RMR. Muñoz-Arroyo
R. Muñoz-Arroyo
HHHéctor Manuel Hdz-García
Héctor Manuel Hdz-García
AEArturo Isaías Martínez Enríquez
Arturo Isaías Martínez Enríquez
MAM. Alvarez-Vera
M. Alvarez-Vera
FHF.A. Hernández-García
F.A. Hernández-García

1 November 2017 in Surface Engineering
Verified
Journal Article
Closed access
JMJ. Molina-Claros
J. Molina-Claros
HHHéctor Manuel Hdz-García
Héctor Manuel Hdz-García
Melvyn Alvarez VeraMelvyn Alvarez Vera
Melvyn Alvarez Vera
MPM. I. Pech-Canul
M. I. Pech-Canul
RMR. Muñoz-Arroyo
R. Muñoz-Arroyo
JDJ.C. Díaz-Guillén
J.C. Díaz-Guillén
Mixtures of Ni-based filler metal without and with 0.5, 1, and 2% WC nanoparticles (NPs) were methodologically tested in order to improve the wear behaviour of WC/Ni-based overlays deposited on low carbon steel by the plasma transferred arc (PTA) process. On adding 2% WC NPs, the longitudinal direction overlay microstructure was modified to have a fibrous appearance. The mechanism to improve WC particle distribution and thus prevent microcrack propagation in the overlays implies a liquid-phase viscosity change. Results of pin-on-disk tests in the overlay using filler metal with 2% WC NPs show that the combined effect of fibrous microstructure and W-rich phases in the overlay, decreases the volume loss by 76% and 78% in comparison with overlays without WC NPs for a 1 and 5 N load, respectively. These outcomes might be of interest for the mining industry, where machinery and equipment are exposed to extreme wear conditions.

1 May 2019 in Vacuum
Verified
Journal Article
Closed access
LSL. Santiago-Bautista
L. Santiago-Bautista
HHHéctor Manuel Hdz-García
Héctor Manuel Hdz-García
RMR. Muñoz-Arroyo
R. Muñoz-Arroyo
MAM. Alvarez-Vera
M. Alvarez-Vera
AGAlejandra Garcia-Garcia
Alejandra Garcia-Garcia
JAJ.L. Acevedo-Dávila
J.L. Acevedo-Dávila

24 December 2014 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
RMR. Muñoz-Arroyo
R. Muñoz-Arroyo
HHHéctor Manuel Hdz-García
Héctor Manuel Hdz-García
JEJosé C. Escobedo-Bocardo
José C. Escobedo-Bocardo
EGEverardo Efren Granda-Gutierrez
Everardo Efren Granda-Gutierrez
JAJ. L. Acevedo-Dávila
J. L. Acevedo-Dávila
AGA. Garza-Gomez
A. Garza-Gomez
In order to improve the Mg removal from an A-380 molten alloy, mixtures of zeolite and SiO2nanoparticles (SiO2(NPs)) were tested. Zeolite was enriched with 2.5, 5, 7.5, 10, or 12.5 wt-% of amorphousSiO2(NPs). TheSiO2(NPs)and zeolite were mixed for 30 min in ethanol for each experiment and then dried in a furnace at 80°C for 12 h. The enriched zeolites were analyzed by scanning electron microscopy, transmission electron microscopy, and N2gas adsorption analysis. The Mg removal was carried out injecting each mixture into the molten aluminum alloy at 750°C using argon. The Mg content of the molten alloy was measured after different periods of the injection time. Zeolites enriched with 2.5 and 5 wt-% ofSiO2(NPs)were demonstrated to be the better mixtures, removing Mg from an initial content of 1.6 to a final content of 0.0002 and 0.0101 wt-%, respectively, in 45 min of injection.