Aerosol-assisted chemical vapor deposition (AACVD) is a technique implicates the atomization of a precursor solution into fine droplets which are dragged by a hot air flow throughout mobile nozzle unto heated reaction zone where occurring chemical reactions. In this work, implementation of the mechanical, electrical and electronic components for AACVD in descriptive way is presented. Equipment and experimental methods implemented are described, together to the automatization criteria of nozzle, temperature control of the heating plate and nebulizing system. The flowchart, the logic sequence of the speed control programming and statistical analysis of the nozzle displacement control were completed and checked, therefore an adequate link between the diverse components via Arduino with the design and automatization criteria was achieved. Finally, we conclude that the criteria and automatization process used permitted successfully to make uniform and reproducible coatings.
We present the design, construction, and implementation of thin film deposition equipment based on the Sol/Gel dip-coating technique for the fabrication of coatings under controlled deposition conditions and working environment at ambient temperature and pressure. The deposition system includes a 304 stainless steel structure and a moving platform that holds the substrate and is transported along vertical axes at a deposition distance of up to 30 cm in height. The mechanical and electronic design was considered, using computer-aided development and dimensional validation (for the structure and the motion transmission system) and the programming of the system using the Arduino platform. The design focused on the deposition speed control for the functional equipment operations, whose operating principle is based on a PWM scheme, achieving an immersion/extraction speed parameter in ranges between 1.5 cm/s and 3.5 cm/s (with a resolution of ± 0.2 cm/s). The operation of the equipment and the reproducibility of the deposits were tested by studying the optical properties of CuCoMn coatings on glass. A substrate immersion/extraction speed of 1.5 cm/s and precursor agitation time (0.83 h - 0.98 h) were used, obtaining absorbances higher than 90%. In conclusion, the implemented prototype will allow the research group to produce reproducible thin films of better quality than those made manually, which can be produced at a low cost and offer the possibility of sustainable maintenance of the equipment.
24 October 2024 in Tendencias en energías renovables y sustentabilidad
El aumento en los costos de energía eléctrica ha despertado un mayor interés en la población en usarla de manera más eficiente. La proliferación de condominios verticales en las ciudades genera desafíos para satisfacer las necesidades de electricidad y gas debido a la alta densidad de habitantes. Aunque los calentadores solares de agua se han vuelto populares, en edificios de más de cinco pisos esta opción es limitada por la distancia y falta de espacio para todos los residentes. En muchos casos, la única opción viable para calentar agua es el uso de gas natural, gas LP o electricidad. En ciudades grandes, el gas natural es común en nuevos edificios, y el uso de gas LP está restringido por motivos de seguridad. Un análisis técnico-económico mostró que, aunque la electricidad no es la forma más eficiente de calentar agua, su costo es más bajo que el del gas natural y LP, gracias a los subsidios gubernamentales para hogares de bajo consumo. En un ejemplo evaluado, el costo del gas natural y LP fueron 2.2 y 1.6 veces más altos que el de la electricidad, lo que hace a esta última una opción más económica.
31 December 2024 in Revista de Ingeniería Industrial
The objective of this work was to design, build and install a device to recover the water wasted in low-cost showers, while waiting for the liquid to reach a comfortable temperature. The novelty of this work is that anybody with basic knowledge of Arduino®, or other open-source microcontrollers can build the system, recovering water and at the same time reducing costs. The system can be installed in any home using the existing water pipelines. In addition, it has a functional, compact and adaptable structure, which does not require modifications in the hydraulic installation nor affect the aesthetics of the place where it will be installed, thus facilitating its implementation in any residential home without the need of complex or expensive renovations.
La técnica de Depósito Químico de Vapor Asistido por Aerosol (AACVD) es un proceso de atomización de la solución precursora, generando gotas que se envían por medio de un gas portador hacia la superficie del sustrato, formando una película delgada cuyas propiedades dependerán de variables como la velocidad de depósito, temperatura del sustrato, tamaño de la gota y número de capas. En éste trabajo se presentan los criterios de diseño mecánico, eléctrico y electrónico empleados para implementar la técnica. El prototipo consiste en una estructura metálica que soporta una placa calefactora y un porta-sustrato donde se ubica la muestra a recubrir; la placa es controlada con un microcontrolador de potencia para mantener constante la temperatura del sustrato. Además, se implementó un sistema de pulverización con un nebulizador ultrasónico 241TM y un sistema de calentamiento de aire con un horno en función rampa MC5438. La tobera de inyección del vapor es guiada por un motor a paso NEMA 17 controlado por Arduino y se desplaza a lo largo del sustrato permitiendo variar la velocidad de depósito, el número de capas, tiempo de retardo entre capas y la distancia a recorrer. Se comparan espectros de transmitancia de películas delgadas de óxido de titanio fabricadas con diferentes parámetros de depósito. En conclusión, con base en los criterios y parámetros de diseño definidos se construyó e implementó la técnica AACVD que permitió fabricar recubrimientos homogéneos con diferentes aplicaciones dependiendo de las sales precursoras y de los parámetros de depósito.