Short-wave infrared (SWIR) imaging systems with unmanned aerial vehicles (UAVs) are rarely used for remote sensing applications, like for vegetation monitoring. The reasons are that in the past, sensor systems covering the SWIR range were too expensive, too heavy, or not performing well enough, as, in contrast, it is the case in the visible and near-infrared range (VNIR). Therefore, our main objective is the development of a novel modular two-channel multispectral imaging system with a broad spectral sensitivity from the visible to the short-wave infrared spectrum (approx. 400 nm to 1700 nm) that is compact, lightweight and energy-efficient enough for UAV-based remote sensing applications. Various established vegetation indices (VIs) for mapping vegetation traits can then be set up by selecting any suitable filter combination. The study describes the selection of the individual components, starting with suitable camera modules, the optical as well as the control and storage parts. Special bandpass filters are used to select the desired wavelengths to be captured. A unique flange system has been developed, which also allows the filters to be interchanged quickly in order to adapt the system to a new application in a short time. The characterization of the system was performed in the laboratory with an integrating sphere and a climatic chamber. Finally, the integration of the novel modular VNIR/SWIR imaging system into a UAV and a subsequent first outdoor test flight, in which the functionality was tested, are described.
Flooding is one of the most common natural disasters, causing emergencies and significant damage to infrastructure. Amid crises, entities such as the World Food Program employ remotely sensed images, usually via drones, to analyze the situation quickly and plan life-saving interventions. Suitable Computer Vision (CV) tools are necessary to assist experts of first responder teams with the analysis of the image data, increasing their productivity and enabling strategic resource allocation. Many state-of-the-art CV-tools use supervised Deep Learning (DL) techniques, for which labeled training data is needed. In this paper, we present the BlessemFlood21 dataset to support the development of DL-based CV-tools for the task of advanced flood analysis in non-coastal river flood scenarios. In particular, we address the problem of segmenting water from RGB images. The presented resulting dataset consists of high-definition, georeferenced RGB images labeled with precise water masks. The water masks are derived using a proposed semi-automatic human-in-the-loop strategy based on the use of additionally imaged NIR data together with a classical Random Forest approach. We assess the resulting dataset and provide a baseline for future advancements in flood mapping by training and evaluating three different state-of-the-art segmentation models (UNet++, DeepLabV3+, SegFormer-B5). Further, we showcase the potential use of the dataset with several experiments. In particular, we compare with the Floodnet dataset and, we employ the segmentation models trained on our dataset together with a Digital Elevation Model to showcase the potential to estimate flood water levels.
Over the Hahnöfer Nebenelbe, a part of the Elbe estuary near Hamburg, Germany, a combined aerial survey with an unmanned aerial system (UAV) and a gyrocopter was conducted to acquire information about the water surface temperatures. The water temperature in the estuary is important for biological processes and living conditions of riverine organisms. This study aimed to develop a workflow that allows for comparing and analysing surface temperatures acquired by two different remote sensing systems. The thermal infrared (TIR) datasets were compared with in situ measurements gathered during the data acquisition, where both TIR datasets showed a varying bias. Potential error sources regarding the absolute and relative accuracy were investigated and modelled based on the available measurements, including emissivity, atmosphere, skin effect at the water surface, camera flat field correction and calibration. The largest effects on the observed TIR water temperature had the camera calibration and the modelled atmospheric effects. After the correction steps, both datasets could be combined to create a multitemporal representation of the temperature pattern and profiles over the survey area’s wadden flats.
17 January 2022 in PFG – Journal of Photogrammetry, Remote Sensing and Geoinformation Science
Airborne remote sensing with optical sensor systems is an essential tool for a variety of environmental monitoring applications. Depending on the size of the area to be monitored, either unmanned (UAVs) or manned aircraft are more suitable. For survey areas starting at several square kilometers, piloted aircraft remain the preferred carrier platform. However, a specific class of manned aircraft is often not considered: the gyrocopter-type ultralight aircraft. These aircraft are less expensive to operate than conventional fixed wings. Additionally, they are highly maneuverable, offer a high payload and a long endurance, and thus perfectly fill the niche between UAVs and conventional aircraft. Therefore, the authors have developed a modular and easy-to-use sensor carrier system, the FlugKit, to temporarily convert an AutoGyro MTOsport gyrocopter into a full-fledged aerial remote sensing platform mainly for vegetation monitoring. Accordingly, various suitable optical sensor systems in the visible (VIS), near-infrared (NIR), and longwave infrared (LWIR) were explicitly developed for this carrier system. This report provides a deeper insight into the individual components of this remote sensing solution based on a gyrocopter as well as application scenarios already carried out with the system.