23 July 2021 in Nature Communications
The emerging field of printed electronics uses large amounts of printing and coating solvents during fabrication, which commonly are deposited and evaporated within spaces available to workers. It is in this context unfortunate that many of the currently employed solvents are non-desirable from health, safety, or environmental perspectives. Here, we address this issue through the development of a tool for the straightforward identification of functional and “green” replacement solvents. In short, the tool organizes a large set of solvents according to their Hansen solubility parameters, ink properties, and sustainability descriptors, and through systematic iteration delivers suggestions for green alternative solvents with similar dissolution capacity as the current non-sustainable solvent. We exemplify the merit of the tool in a case study on a multi-solute ink for high-performance light-emitting electrochemical cells, where a non-desired solvent was successfully replaced by two benign alternatives. The green-solvent selection tool is freely available at: www.opeg-umu.se/green-solvent-tool.
18 July 2024 in Advanced Science
Carbon dots (CDs) are an emerging class of nanomaterials with attractive optical properties, which promise to enable a variety of applications. An important and timely question is whether CDs can become a functional and sustainable alternative to incumbent optical nanomaterials, notably inorganic quantum dots. Herein, the current CD literature is comprehensively reviewed as regards to their synthesis and function, with a focus on sustainability aspects. The study quantifies why it is attractive that CDs can be synthesized with biomass as the sole starting material and be free from toxic and precious metals and critical raw materials. It further describes and analyzes employed pretreatment, chemical‐conversion, purification, and processing procedures, and highlights current issues with the usage of solvents, the energy and material efficiency, and the safety and waste management. It is specially shown that many reported synthesis and processing methods are concerningly wasteful with the utilization of non‐sustainable solvents and energy. It is finally recommended that future studies should explicitly consider and discuss the environmental influence of the selected starting material, solvents, and generated byproducts, and that quantitative information on the required amounts of solvents, consumables, and energy should be provided to enable an evaluation of the presented methods in an upscaled sustainability context.
13 October 2021 in ACS Sustainable Chemistry & Engineering
We present the synthesis and characterization of an efficient and low cost solar-driven electrolyzer consisting of Earth-abundant materials. The trimetallic NiFeMo electrocatalyst takes the shape of nanometer-sized flakes anchored to a fully carbon-based current collector comprising a nitrogen-doped carbon nanotube network, which in turn is grown on a carbon fiber paper support. This catalyst electrode contains solely Earth-abundant materials, and the carbon fiber support renders it effective despite a low metal content. Notably, a bifunctional catalyst–electrode pair exhibits a low total overpotential of 450 mV to drive a full water-splitting reaction at a current density of 10 mA cm–2 and a measured hydrogen Faradaic efficiency of ∼100%. We combine the catalyst–electrode pair with solution-processed perovskite solar cells to form a lightweight solar-driven water-splitting device with a high peak solar-to-fuel conversion efficiency of 13.8%.
13 January 2021 in ACS Applied Nano Materials
1 November 2023 in Green Chemistry
A mild solvothermal synthesis of carbon dots (CDs) from birch leaves is reported. The CDs feature a high quantum yield of 26% in ethanol, and deliver deep-red, narrowband emission (λpeak = 675 nm, FWHM = 29 nm) in a light-emitting device.
22 January 2024 in Applied Physics Letters
All-inorganic perovskite quantum dots (PeQDs) have aroused great research interest in white light-emitting diodes (WLED) due to their excellent optoelectronic properties, but the poor stability, caused by dynamically binding long-chain capping ligands, hinders their future practical applications. To address this issue, here, we exploit short-chain butyric acid (BA) to replace long-chain oleic acid (OA) as capping ligand of CsPbX3 PeQDs by a hot-injection method. The addition of BA not only makes the morphology of CsPbBr3 PeQDs uniform and improves the crystallinity but also effectively suppresses nonradiative recombination, achieving a near unit photoluminescence quantum yield of 96%. The BA capped CsPbBr3 PeQDs exhibit high stability up to 180 d stored in ambient environment and also significantly improved resistance against polar solvent, ultra-violet lamp irradiation, and heat, which is rationalized by the strong binding capacity and shortened distance of BA to the PeQDs through ab initio calculations. Furthermore, by combining green-emission CsPbBr3 and red-emission CsPbBr0.8I2.2 PeQDs with blue GaN chip, we achieved WLEDs with excellent luminous properties, showing their great potential in practical application of wide-color-gamut display and lighting.