28 May 2020 in Applied Physics Express
17 January 2022 in IEEE Transactions on Electron Devices
This article presents improvements of large-signal RF power performance at Ka-band of gallium nitride high electron mobility transistors (HEMTs) utilizing a scandium aluminum nitride barrier. Three samples were fabricated and measured having different passivation schemes, including gallium nitride, silicon nitride, and aluminum gallium nitride. The pinning of the Fermi level against the valence band reduced the gain and output power density of the gallium nitride passivated device, resulting in 4.5 W/mm at a drain bias of 32 V. With silicon nitride alone as the passivation, dc/RF dispersion was reduced, and gain increased significantly, boosting the output power for this device to 8.0 W/mm at 28 V, though at the cost of a reduced breakdown voltage. Adding an epitaxial aluminum gallium nitride passivating layer increased the maximum bias voltage that the devices can operate at compared to devices with the silicon nitride passivation. When biased at 40 V, the output power of the devices reached 10.8 W/mm at 30 GHz. These devices show the importance of the passivation design to large-signal RF performance in scandium aluminum nitride-based HEMTs and will help guide further improvements.
8 October 2018 in IEEE Electron Device Letters
We report on the power and linearity performance of metal organic chemical vapor deposition (MOCVD) grown AlGaN channel polarization-graded field-effect transistor (PolFET). The fabricated transistors with 3-dimensional electron channels showed nearly flat transconductance profiles. Maximum fT and fmax of 23 GHz and 65 GHz were measured for 0.7 μ m gate-length transistors, corresponding to an fT-LG product of 16.2 GHz-μm. Load-pull measurement at 10 GHz revealed a maximum output power of 2 W/mm with a maximum small signal gain of 16 dB. Two tone measurement at 10 GHz showed an OIP3 of 33 dBm for 150 μm device width, and a corresponding linearity figure of merit OIP3/PDC of 3.4 dB. These results suggest that PolFETs could be useful for high frequency applications requiring high linearity.
11 August 2016 in IEEE Transactions on Semiconductor Manufacturing
In this paper, electrical characterization results of N-polar GaN high-electron-mobility transistors that have been released from a 6H-SiC wafer and manually transferred to a Si wafer using a novel epitaxial lift-off (ELO) technique are presented. This recently developed ELO method uses a thin sacrificial layer of Nb2N, a hexagonal epitaxial conductor with less than 1% lattice mismatch to 4H- and 6H-SiC, to serve as the template for III-N device heterostructure growth. Measured results of transferred devices indicate that electron transport properties and low power density electrical performance are nominally unchanged relative to values measured before release. This technique has several advantages over competing ELO techniques, such as the well-known smart cut method, including bonding-ready released material with atomically-smooth backsides (≤ 0.5 nm rms), easy substrate reclaim with indefinite recycling potential, and a transfer process that can be performed after full front-side device processing and yield screening has been completed.
6 September 2017 in IEEE Transactions on Semiconductor Manufacturing
Although selective dry etches exist for GaN, it is difficult to selectively etch AlN in heterostructures with other conventional III-N epitaxial materials. The reduction in etch rate resulting from the addition of 2-16% scandium to ScxAl₁-xN in conventional Cl₂/BCl₃/Ar inductively coupled plasma etching is presented. Smooth, epitaxial ScxAl₁-xN layers are grown by RF-plasma-assisted molecular beam epitaxy directly on 4H-SiC substrates. The etch selectivity with respect to AlN is as high as 10.6 and 11.2 for x = 0.02 and 0.16, respectively, allowing ScxAl₁-xN to act as an etch-stop layer with minimal misfit strain when grown within either AlN or GaN based heterostructures.