In developing a new field or reservoir, many parameters are important in understanding the success or possible areas for improvement in hydraulic fracturing. Estimating fracture geometry is essential to effectively calibrate a reservoir model to production results. Radioactive (RA) tracers have been used in hydraulic fracturing treatments to infer fracture dimensions. Three stable isotopes (i.e. Scandium, Iridium and Antimony) were used in various parts of the treatment to understand the progression of hydraulic fracture growth. Advanced sonic anisotropy logging tools, using a broader range of frequency acquisition, were used to enable shear measurement in cased hole environments over a wide range of interbedded coal, shale and sandstone sequences both before and after the hydraulic fracture treatment. Amplitude and anisotropy changes after a hydraulic fracture have been measured using sonic anisotropy logging and used to infer fracture height. Finally, the sonic anisotropy can be evaluated above and below the perforated interval and investigate hydraulic fracture height growth away from the wellbore, potentially visualising a greater distance than available with RA tracers. We will show how sonic anisotropy and radioactive tracer logging methods can be used to better understand the fracture geometry and aid further design work. The paper will present data from two (2) wells in the Walloon Coal Measures of the Surat Basin where both RA tracers and sonic anisotropy logs were used to infer fracture dimensions. Both wells used a combination of treated water stages, containing low concentrations of proppant, followed by borate-crosslinked gelled water stages with higher concentrations of proppant. This project contained a large amount of other hydraulic fracturing diagnostics including treatment pressure history- matching, microseismic monitoring and surface tiltmeters. In this paper we will note how those diagnostics compared with the results presented herein, but their results are discussed in greater detail elsewhere (Johnson et al. 2010a). Generally, the results indicate good agreement between these two fracture diagnostic methods and the authors will illustrate the complimentary nature of these diagnostics in gaining a fuller understanding of fracture height, especially in environments of complex fracture development.
In coal seam gas (CSG), also known as coalbed methane (CBM), appraisal, the development potential of a play requires an understanding of the interrelationship between stress and permeability, critical elements in defining deliverability and hydraulic fracturing effectiveness. Unfortunately, the interdependency of these variables may not emerge until the post-treatment evaluation of a hydraulic fracturing treatment. Herein is an example from the Walloon Subgroup (WSG), Surat Basin, where regional data were used to target a small, localized, structural setting for CSG appraisal and subsequent hydraulic fracturing. Due to the rank of the WSG coals in this area, the cleat network was deemed to be immature and permeability is understood to be derived from exogenetic fracturing from external stresses acting on the coal, creating a unidirectional fracture network. The fractures are commonly constrained to brittle lithologies and truncate at bedding boundaries, while evidences exist of minor low angle faulting in non-reservoir lithologies. Eventually, the local stress regime was determined from the petrophysical log data, injection stress testing, and subsequent one-dimensional (1D) mechanical earth model (MEM). Ultimately, these data support the proposed reservoir and stress environment. We will show how data were acquired, evaluated and integrated to support the development of the 1D MEM and aided the interpretation of the hydraulic fracture treatment results. While localized, the results of this evaluation indicate a potential pitfall can exist in some CSG environments. This case illustrates a scenario where stress and dominant permeability axes can be properly aligned to maximize hydraulic fracture effectiveness, but where sub-optimal stress magnitudes prevent achieving the full benefit of the hydraulic fracturing process.
In developing new coalbed methane (CBM) or coal seam gas (CSG) fields or reservoirs, the effect of many parameters are important in understanding the success or potential areas for improvement of hydraulic fracturing treatments. Estimating fracture geometry relative to the reservoir architecture is critical to understanding production variability. The Walloon Coal Measures, in the Surat Basin of Eastern Queensland, Australia, are a complex reservoir containing interbedded sandstone, siltstone, carbonaceous shale and coal seams where initial attempts at hydraulic fracturing in early pilot areas of the Surat Basin yielded poor results. Thus, when a hydraulic fracturing program was planned for this reservoir, it was decided to integrate a group of diagnostics that would be useful in understanding past results as well as deriving future improvements. Data is presented from two wells in the Walloon Sub Group (WSG) where tiltmeters and microseismic monitoring were used to evaluate fracture effectiveness relative to the reservoir architecture and to assist further design work. The treatments carried out in the studied wells were typical of CSG frac treatments used in other producing areas, incorporating stages of treated, gelled and crosslinked-gelled water with increasing concentrations of sand, up to six (6) lbm/gal. During the treatments, complex fractures were inferred based on analyses of data from both tiltmeter and microseismic monitoring methods. The collaborative data set for these wells also included a large amount of other analyses and diagnostic data. It was only possible to fully explain the treatment results through the combination of multiple diagnostics and an in-depth understanding of how the created fracture interacted with the complex reservoir and stress environment. In this paper, we outline the steps used to plan the monitoring program and describe how geological data was integrated to better understand the results observed during the treatments. We describe each of six (6) stages performed across the two wells, and how the diagnostics did or did not support the overall conclusions as to the effectiveness of each stage. Finally, this paper presents a logical framework to evaluate and integrate these technologies for use in future CSG well stimulation.