10 February 2020 in Journal of the American Chemical Society
A combination of X-ray ptychography and X-ray fluorescence tomography (XRF) has been used to study the fragmentation behavior of an individual Ziegler-Natta catalyst particle, ~40 microns in diameter, in the early stages of propylene polymeri-zation with sub-micron spatial resolution. The electron densi-ty signal obtained from X-ray ptychography gives the compo-site phases of the Ziegler-Natta catalyst particle fragments and isotactic polypropylene, while 3-D XRF visualizes multiple isolated clusters, rich in Ti, of several microns in size. The radial distribution of Ti species throughout the polymer-catalyst composite particle shows that the continuous bisec-tion fragmentation model is the main contributor to the frag-mentation pathway of the catalyst particle as a whole. Fur-thermore, within the largest Ti clusters the fragmentation pathway was found to occur through both the continuous bisection and layer-by-layer models. The fragmentation behav-ior of polyolefin catalysts was for the first time visualized in 3-D by directly imaging and correlating the distribution of the Ti species to the polymer-catalyst composite phase.
29 June 2021 in Catalysis Science & Technology
Efficient fragmentation of catalyst particles during the polymerization of olefins is a necessary process to maintain catalyst activity and obtain discrete polymer particles with ideal density and morphology. Collecting experimental evidence on the fragmentation process is essential for a fundamental understanding of this phenomenon. However, visualizing the very early onset of fragmentation within catalyst particles has been proven challenging. This study investigates the development of fragmentation at different reaction conditions in an industrial SiO2-supported metallocene catalyst of the type Zr/MAO/SiO2 (MAO = methylaluminoxane) early-stage of ethylene polymerization, i.e., in the range 1–20 g polyethylene per g catalyst. Focused ion beam-scanning electron microscopy was employed to visualize particle cross-sections with high 2-D resolution (i.e., a few tens of nm), showing that ethylene polymerization starts at two main fronts: one at the outer surface and one at the walls of the macropores within the particle. The relative rate of polymerization at these fronts was assessed by estimating the extent of polyethylene, catalyst, and macroporosity within each cross-section via image segmentation. When polymerization at these fronts proceeds at similar rates, fragmentation is extensive and a combination of both layer-by-layer and bi-sectioning modes; conversely, an imbalance between the two due to unideal reaction conditions, non-homogeneous active site distribution, or insufficient macroporosity leads to a sub-optimal fragmentation. This methodology revealed a detailed understanding of catalyst fragmentation for this commercial catalyst. However, it can be applied to a broader range of polymerization catalysts and parameters, amplifying the knowledge on such an intricated phenomenon.
16 September 2019 in ACS Applied Materials & Interfaces
The synthesis and characterization of highly stable and conductive F:SnO2 (FTO) nanopyramid arrays are investigated, and their use as scaffolds for water splitting is demonstrated. Current densities during the oxygen evolution reaction with a NiFeOx catalyst at 2 V vs reversible hydrogen electrode were increased 5-fold when substituting commercial FTO (TEC 15) by nanostructured FTO scaffolds. In addition, thin α-Fe2O3 films (∼50 nm thick) were employed as a proof of concept to show the effect of our nanostructured scaffolds during photoelectrochemical water splitting. Double-layer capacitance measurements showed a drastic increase of the relative electrochemically active surface area for the nanostructured samples, in agreement with the observed photocurrent enhancement, whereas UV–vis spectroscopy indicates full absorption of visible light at wavelengths below 600 nm.
26 July 2018 in Chemphyschem
MVMarjolein E. Z. Velthoen
+4
1 December 2021 in Chem Catalysis
3 May 2023 in ChemCatChem
A commercial SiO2 modified by the addition of a TiO2 layer on its surface and pore walls offers a support for metallocene‐based ethylene polymerization catalysts with a 35 % improved catalytic activity. The effect of such support modification on the catalyst particle fragmentation during polymerization reactions were assessed. This was performed by exposing the internal cross‐section of several SiO2 and Ti/SiO2‐based metallocene catalyst particles, polymerized at a wide range of reaction conditions, with a Focused‐Ion Beam Scanning Electron Microscope (FIB‐SEM), followed by a semi‐quantitative analysis of polymer, catalyst and macropores of each 2D image obtained. The titanation of the SiO2 lead to a support framework that fractures earlier and more efficiently. This was evidenced by the presence of several empty (polymer‐free) cracks along the support dense‐shell, found more extensively in the Ti‐modified polymerized catalyst particle, which also resulted in a more sustained polymerized particles macroporosity during the course of the reaction.