1 April 2014 in The Journal of Prosthetic Dentistry
1 October 2015 in The Journal of Prosthetic Dentistry
1 April 2019 in Journal of Prosthodontic Research
RSRenata Bacelar Catanhede de Sá
Renata Bacelar Catanhede de Sá
+2
The aim of this study was to evaluate the influence of indirect restorative material type and thickness on the transmission of different wavelengths from a broad-banded dental curing light. Four dental indirect restorative materials for computer-aided design and computer-aided manufacturing (CAD/CAM) were evaluated: [RC] resin/ceramic hybrid material (Lava Ultimate), [FC] feldspathic ceramic (VitaBlocs), and two zirconia-based ceramics ([ZK] Katana; and [ZL] Lava). Total loss of irradiance (TL) was measured for blue (WB, 425-490nm) and violet (WV, 350-425nm) wavelengths. Specimens of 15×15mm with varying thicknesses (0.5, 1.0, 1.5, and 2.0mm) were fabricated (n=5). A plasma-arc dental light-curing unit was used (Arc Light-II). To assess TL as a function of wavelength, a software (Spectra Suite v5.1) connected to a spectroradiometer (USB2000) and an integrating sphere (CTSM-LSM-60-SF) was used. Data was subjected to statistical analysis (two-way ANOVA and post-hoc Tukey test, α=0.05). A 0.5mm interposition resulted in TL from 50.5 to 67.2%, depending on material. Increased thickness resulted in higher TL for all materials. FC showed less TL compared to ZK. In general, WV showed higher TL than did WB, and WV/WB proportion decreased with increasing thickness. Indirect materials significantly reduced TL, and this effect is greater with increasing thickness. WV showed lower penetration compared to WB.
1 November 2011 in Photomedicine and Laser Surgery
MOMarcelo Tavares de Oliveira
Marcelo Tavares de Oliveira
PFPatrícia Moreira de Freitas
Patrícia Moreira de Freitas
AAAna Cecília Corrêa Aranha
Ana Cecília Corrêa Aranha
+1
Objective:
The purpose of this study was to evaluate the effects of Er,Cr:YSGG laser irradiation and different adhesive procedures on bond strength of two bonding agents to dentin.
Background data:
Studies have shown that laser-irradiated dentinal tissue yields lower bond strengths than does nonirradiated dentin. In this study, different treatment methods of laser irradiating dentin were studied to enhance the bond strength of bonding agents to nonirradiated dentin.
Methods:
Third molars were wet ground with SiC until the occlusal flat dentin surface was exposed, and the teeth were randomly assigned to six groups ( n =5). A two-step self-etching primer (Clearfil SE Bond, G1) and a two-step etch-and-rinse adhesive (Single Bond Plus, G2) were applied to the nonirradiated dentin surface according to manufacturer's instructions, as control groups. In G3 and G4, the same adhesives were applied after Er,Cr:YSGG laser irradiation, whereas in G5 and G6 adhesives were applied after Er,Cr:YSGG laser irradiation, phosphoric acid etching, and NaOCl deproteinization of etched dentin. The Er,Cr:YSGG laser worked at 2.78 μm and the repetition rate was fixed at 20 Hz. Composite blocks were built on bonded surfaces and the teeth were stored for 24 h at 37°C. Restored teeth were vertically and serially sectioned to obtain bonded specimens for the bond strength test. Data were analyzed by two-way ANOVA and Tukey test (α=5%).
Results:
Laser irradiation reduced bond strengths for the two adhesives, regardless of acid etching and deproteinization of dentin post-irradiation ( p <0.05). The self-etching primer system showed higher bond strengths to laser irradiated dentin than did Single Bond Plus ( p <0.05). The adhesive systems applied to normal dentin yielded higher bond strengths than when they were applied to laser irradiated dentin ( p <0.05).
Conclusions:
The self-etching primer seemed to be less affected by dentin irradiation with Er,Cr:YSGG laser. The additional etching and NaOCl solution did not overcome the effects of laser irradiation on dentin.
14 August 2012 in Brazilian Oral Research
MOMarcelo Tavares de Oliveira
Marcelo Tavares de Oliveira
This study evaluated the effect of adhesive systems and application strategies on dentin hydraulic conductance (HC). The buccal enamel was removed from bovine incisors to simulate laminate cavity preparations. After removing the roots and the coronal pulp, the buccal dentin was treated with EDTA solution (0.5 M) for 5 minutes, rinsed, ultrasonicated for 12 minutes and connected to a permeability device. HC of the specimens was measured at 10 psi (n = 5). Permeability was measured before and after bonding procedures using G-Bond (GB), Clearfil Tri-S Bond (CTS), Hybrid Coat (HY), Bond Force (BF), Adper Easy Bond (AEB) Silorane (SI), Clearfil SE Bond (CSE) and Adper Scotchbond Multi-Purpose (SMP) adhesives systems, which were applied following three strategies: 1) according to the manufacturers' instructions; 2) two coats of all-in-one self-etching adhesives (GB, CTS, HY, BF, AEB) or priming step plus two coats of bonding resin for the other systems (SI, CSE and SMP); and 3) a thin layer of a flowable composite applied over one coat of all-in-one self-etching adhesives or primed surface for SI, CSE and SMP adhesives. No significant difference was observed among the application modes concerning their ability to reduce HC. None of the adhesives showed complete sealing (100%) of the bovine tooth dentin. SI exhibited lower HC than SMP, however, they were not significantly different from the other systems. The results suggest that all systems tested result in an HC reduction of more than 90%. The wet bonding technique seemed to be more sensitive for dentin sealing.
1 August 2015 in Brazilian Dental Journal
RBRenata Cantanhede Bacelar-Sá
Renata Cantanhede Bacelar-Sá
+1
This study evaluated the effects of indirect restorative materials, curing conditions and time on the degree of conversion (DC) of a dual-cured resin cement using infrared spectroscopy. The resin cement (RelyX Unicem 2, 3M ESPE) was applied to the diamond surface of a horizontal attenuated-total-reflectance unit and activated using one of following conditions: self-cure, direct light exposure, light exposure through indirect restorative materials (resin nano-ceramic: Lava Ultimate, 3M ESPE or feldspathic ceramic: Vita Blocks Mark II, Vita Zahnfabrik). Four thicknesses (0.5, 1.0, 1.5 or 2.0 mm) of each indirect material were analyzed, and the light-activation was performed using a blue LED light. Data (n=5) were analyzed by three-way ANOVA, Tukey's post hoc and Dunnett's tests (α=5%). No significant differences in DC were observed between indirect materials of similar thickness. All groups exhibited higher DC after 10 min than after 5 min. At both times points, the self-cure group exhibited significantly lower DC than all the light exposure groups. Only when the overlying indirect restoration had a thickness of 2 mm did DC decrease significantly. The presence of a thick, indirect restoration can decrease the DC of resin cement. DC after 10 min was higher than after 5 min. The self-cure mode yielded lower DC than the light-activating one.