Joshua Claudio Andre Yanapa Marquez

Joshua Claudio Andre Yanapa Marquez

Auto-generated profile, based on publicly available information

Joshua Claudio Andre Yanapa Marquez

Carrera de Estomatología, Universidad Científica del Sur. Lima, Perú

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 March 2024 in Revista Científica Odontológica
Verified
Journal Article
Open access
PDF file
JMJoshua Yanapa Márquez
Joshua Yanapa Márquez
MCMartín Andrés Chavez-Méndez
Martín Andrés Chavez-Méndez
Introduction: In oral rehabilitation, the use of ceramic restorations is widely accepted due to its aesthetic capacity to mimic the naturalness of the dental tissue, provide longevity of the material, and present a greater marginal fit compared to crowns with a metal structure. Termination lines are biological preparations whose function is to minimize the cervical opening of the marginal seal. Consequently, analyzing the behavior of restorative materials under compressive forces decreases the risk of fracture and increases the success of the treatment. Objective: To compare the compressive stresses of lithium disilicate crowns with three different finishing lines. Methodology: In silico study of the simulation of a dental preparation on a lower right first molar with chamfer (0.6 mm), shoulder (0.5 mm) and deep chamfer (0.5 mm) finish lines. Using the SolidWorks®️ version 2017 software, the maximum stresses, minimum stresses, and location of the compressive force were collected on the Megapascal (Mpa) measurement scale. Results: The chamfer type termination line (0.6mm) obtained a lower compressive stress compared to the other two shoulder type termination lines (0.5mm) and deep chamfer (0.5mm). Conclusions: It was shown that the chamfer type finishing line (0.6mm) presented a better force distribution, determining greater reliability in the selection of this finishing line with the use of a lithium disilicate crown in a unitary manner.

5 February 2024
Verified
Thesis
Open access
JMJoshua Claudio Andre Yanapa Marquez
Joshua Claudio Andre Yanapa Marquez
Introducción: En rehabilitación oral es ampliamente aceptado el uso de restauraciones cerámicas por su capacidad estética para mimetizar la naturalidad del tejido dentario, brindar longevidad del material y presentar un mayor ajuste marginal en comparación a coronas con estructura metálica. Las líneas de terminación son preparaciones biológicas cuya función es minimizar la abertura cervical del sellado marginal. En consecuencia, analizar el comportamiento de materiales restauradores bajo fuerzas compresivas, disminuye el riesgo de fractura y aumentan el éxito del tratamiento. Objetivo: Comparar las tensiones compresivas de las coronas de disilicato de litio con tres distintas líneas de terminación. Metodología: Estudio in silico de la simulación de una preparación dental sobre una primer molar inferior derecha con líneas de terminación tipo chamfer (0,6 mm), hombro (0,5 mm) y chamfer profundo (0,5 mm). Mediante el software SolidWorks®️ versión 2017 se recolectaron las tensiones máximas, tensiones mínimas y localización de la fuerza compresiva en la escala de medición Megapascales (Mpa). Resultados: La línea de terminación tipo chamfer (0.6mm) obtuvo una tensión compresiva menor en comparación de las otras dos líneas de terminación tipo hombro (0,5 mm) y chamfer profundo (0,5 mm). Conclusiones: Se demostró que la línea de terminación tipo chamfer (0.6mm) presentó una mejor distribución de fuerza, determinando una confiabilidad mayor en la selección de esta línea de terminación con el uso de una corona de disilicato de litio de manera unitaria.