James Allan

James Allan

Auto-generated profile, based on publicly available information

James Allan

Urban Energy Systems Laboratory, Empa

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2022 in Building and Environment
Verified
Journal Article
Open access
AMAvichal Malhotra
Avichal Malhotra
JBJulian Bischof
Julian Bischof
ANAlexandru Nichersu
Alexandru Nichersu
KHKarl-Heinz Häfele
Karl-Heinz Häfele
JEJohannes Exenberger
Johannes Exenberger
GSGerald Schweiger
Gerald Schweiger

30 June 2015 in Energy Science & Engineering
Verified
Journal Article
Open access
PDF file
JAJames Allan
James Allan
ZDZahir Dehouche
Zahir Dehouche
SSSinisa Stankovic
Sinisa Stankovic
LMLascelle Mauricette
Lascelle Mauricette
This work details a methodology to characterize the performance of solar thermal and photovoltaic thermal (PVT) collectors using an indoor solar simulator. In this study, several cases have been compared to show that the methodology can be used to extract fundamental performance characteristics from a solar collector. In the first case, a serpentine collector was compared against a header riser collector using the same mass flow rate. It was found that the header riser was less efficient, with a 34% increase in the overall loss coefficient. The experimental results were compared with commonly used empirical models and showed a close agreement. In the second case, the impact on performance of using a polycarbonate cover is presented. The results show that the optical efficiency of the collector is reduced by 12% when using a cover; however, because the loss coefficient is reduced by 53%, the covered collector performs better when there is a large temperature difference between the absorber and the ambient. The third case investigates the combined performance of a PVT collector, that produces both heat and electricity from a single device. By placing photovoltaic (PV) laminates on top of the serpentine absorber, the thermal efficiency is reduced by 15%. When electricity is generated by laminates, the thermal efficiency is reduced by a further 3.5%; this drop in thermal efficiency is a result of the incident radiation producing electricity before reaching the thermal absorber. The combined efficiency of the PVT collectors was compared at controlled inlet temperatures. The serpentine design had the highest combined efficiency of 61% with 8% electricity at the lowest inlet temperature (21°C). The dominant form of loss in the PVT system is temperature driven; as the thermal efficiency decreases, electricity generation makes up a larger percentage of the combined output. This study highlights the potential for manufacturers of bespoke thermal absorbers and PV devices to combine their products into a single PVT device that could achieve improved efficiency over a given roof area.

30 March 2022 in Applied Energy
Verified
Journal Article
Open access
IPIvalin Petkov
Ivalin Petkov
GMGeorgios Mavromatidis
Georgios Mavromatidis
CKChristof Knoeri
Christof Knoeri
JAJames Allan
James Allan
VHVolker H. Hoffmann
Volker H. Hoffmann

1 March 2016 in AIP Advances
Verified
Journal Article
Open access
PDF file
JAJ. Allan
J. Allan
HPH. Pinder
H. Pinder
Zahir DehoucheZahir Dehouche
Zahir Dehouche
Samples of Ethylene-Vinyl Acetate (EVA) were doped with particles of Boron Nitride (BN) in concentrations ranging from 0-60% w/w. Thermal conductivity was measured using a Differential Scanning Calorimetery (DSC) technique. The thermal conductivity of parent EVA was increased from 0.24W/m ⋅ K to 0.80W/m ⋅ K for the 60% w/w sample. Two PV laminates were made; one using the parent EVA the other using EVA doped with 50% BN. When exposed to a one directional heat flux the doped laminate was, on average, 6% cooler than the standard laminate. A finite difference model had good agreement with experimental results and showed that the use of 60% BN composite achieved a PV performance increase of 0.3% compared to the standard laminate.

17 July 2017 in Journal of Solar Energy Engineering
Verified
Journal Article
Closed access
PDF file
JAJames Allan
James Allan
Zahir DehoucheZahir Dehouche
Zahir Dehouche
SSSinisa Stankovice
Sinisa Stankovice
AHAlan Harries
Alan Harries
Numerical simulation enables the optimization of a solar collector without the expense of building prototypes. This study details an approach using computational fluid dynamics (CFD) to simulate the performance of a solar thermal collector. Inputs to the simulation include; heat loss coefficient, irradiance, and ambient temperature. A simulated thermal efficiency was validated using experimental results by comparing the calculated heat removal factor. The validated methodology was then applied to five different inlet configurations of a header–riser collector. The most efficient designs had uniform flow through the risers. The worst performing configurations had low flow rates in the risers that led to high surface temperatures and poor thermal efficiency. The calculated heat removal factor differed by between 4.2% for the serpentine model and 12.1% for the header–riser. The discrepancies were attributed to differences in thermal contact between plate and tubes in the simulated and actual design.