3 December 2021 in IEEE Photonics Technology Letters
A Mach-Zehnder interferometer, composed of two core-offset tapered joints (COTJ-MZI), is proposed and experimentally verified for high sensitivity strain sensing. The COTJ-MZI is handily fabricated by core-offset fusion splicing and tapering based on all single-mode fiber (SMF). The fiber cores form stepped cores within the COTJs. The transmission spectra with different core-offset values and interference lengths are obtained and theoretically analyzed. Benefitting from the stepped cores in the COTJ structure, the mode coupling points are able to be modulated easily by the applied strain. A strain sensitivity of −108.0 pm/ $\mu \varepsilon $ (0- $400~\mu \varepsilon$ ) and −47.6 pm/ $\mu \varepsilon $ (400-1200 $\mu \varepsilon$ ) is achieved. In addition, the temperature response is also characterized as low as 23.3 pm/°C. With the advantages of low cost and high sensitivity, the COTJ-MZI sensor is competitive candidates in the field of strain measurement.
1 June 2023 in Sensors and Actuators A: Physical
7 April 2023 in IEEE Sensors Journal
In this paper, we present and verify the mode dependence of refractive index (RI) sensitivity of long-period fiber grating induced by periodically embedded multimode fiber (PEM-LPFG). The PEM-LPFG is firstly fabricated by periodically embedding multimode fiber (MMF) into the single mode fiber (SMF). The resonant mode is translated by reducing the cladding. Numerical simulations based on beam propagation method (BPM) are applied to calculate the transmission spectrum, mode distribution, and RI sensitivities of the PEM-LPFG. The cladding diameter after etching is determined to be 89 μm and 68 μm, which corresponds to the mode translated from LP 012 to LP 07 and LP 05 , respectively. The experimental results indicate that the maximum refractive index sensitivity of 1322.26 nm/RIU in the range of 1.333 -1.437 RIU is achieved when the resonant mode is LP 07 , which is 4 times as large as the original one (325.58 nm/RIU @ LP 012 mode). PEM-LPFG working at LP 05 mode exhibits a lower sensitivity of 844.72 nm/RIU. All of the experimental results are in good agreement with the simulation. The RI sensitivity optimization of PEM-LPFG is able to realize by mode converting. Furthermore, the temperature responses are measured to be 13 pm/°C and 4 pm/°C. This work provides a theoretical reference and experimental evidence for the dependence of the PEM-LPFG RI sensitivity on the resonant mode for the first time.
15 September 2021 in IEEE Sensors Journal
We proposed and experimentally demonstrated a vector bending sensor based on a core-offset long period fiber grating (CO-LPFG). The CO-LPFG is configured by CO 2 laser polishing on three mutually orthogonal planes of a single mode fiber (SMF) to different depths and then heating it by the electrical arc-discharge of a fusion splicer. The asymmetrical cladding structure leads to an uneven density distribution of the fiber in the molten state. Under the effects of releasing the residual stress and fiber surface tension, the fiber core deviates toward the polished deeper directions to form a core-offset structure in two dimensions. The experimental results demonstrate that the bending sensitivities of CO-LPFG reach 37.06 nm/m −1 −5.85 nm/m −1 -14.59 nm/m −1 and −12.45 nm/m −1 for four bending directions within the range of 1.12-2.10 m −1 The temperature sensitivity of CO-LPFG is 57.90 pm/°C in the range of 40-160°C.
1 August 2023 in Optics Express
Biology, medicine, and chemistry all rely heavily on highly sensitive optical fiber temperature sensors. To the best of our knowledge, this research introduces a unique design framework for high-performance fiber temperature sensors that helps eliminate the all-fiber interferometers’ sensitivity bottleneck. A section of photopolymerized waveguide is embedded in a typical Mach-Zehnder interferomenter framework with multimode fiber-single mode fiber-multimode fiber (MSM) structure. The thermal-optical coefficient (TOC) of the photopolymerized waveguide core, which is created via the fiber-end lithography technique, differs dramatically from that of the resin cladding. Due to the considerable TOC difference, the phase difference between the interfering beams significantly increases as the temperature changes. The fundamental variables affecting temperature sensitivity are conceptually explored and experimentally verified. The suggested device achieves a typical temperature sensitivity of 1.15 nm/∘C in the range of 30–100∘C, which is about 10 times as high as that of the all-fiber MSM sensors. The suggested designing framework offers a fresh thought for creating high-performing fiber optic temperature sensors.
6 December 2022 in IEEE Photonics Technology Letters
A novel tapered two-mode fiber embedded long-period fiber grating (TTMF-LPFG) sensor is proposed. The long-period fiber grating (LPFG) is fabricated by periodically splicing the two-mode fiber (TMF) and single-mode fiber (SMF), and then the LPFG is tapered to make a refractive index (RI) sensor. By comparing the sensors with different waist diameters, we found that the smaller the diameter of the sensor is, the higher the sensitivity is. When the taper waist diameter is 36 $\mu \text{m}$ , the maximum sensitivity reaches 1360.43 nm/RIU. TTMF-LPFG shows low sensitivity to the temperature, avoiding the influence of temperature. For the traditional taper fiber, a very thin taper waist is required to excite strong evanescent field (EF) in order to obtain a large RI sensitivity. This situation creates a sensor fragile. For our structure, through the taper, LPFG can be formed and the sensitivity can be improved at the same time. The sensor has great potential in chemical composition analysis and biomedical applications.