Bo Diao

Bo Diao

Auto-generated profile, based on publicly available information

Bo Diao

School of Transportation Science and Engineering, Beihang University, Beijing 100191, China

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2011 in Journal of Cold Regions Engineering
Verified
Journal Article
Closed access
BDBo Diao
Bo Diao
YSYang Sun
Yang Sun
Shaohong ChengShaohong Cheng
Shaohong Cheng
YYYinghua Ye
Yinghua Ye
The effects of mixed corrosion and freeze-thaw cycles on the mechanical properties of concrete prism specimens and the effects of mixed corrosion, freeze-thaw cycles, and persistent loads on the structural behavior of reinforced concrete beams were experimentally studied. A mixed solution of NaCl and Na2SO4 was used as a corrosive medium. Results show that under alternating actions of freeze-thaw and mixed corrosive agents, increasing the number of freeze-thaw cycles decreases the compressive strength and the elastic modulus of concrete and increases the compressive strain corresponding to the maximum compressive stress. The degradation of concrete material properties accelerates with the increase of water-cement ratio. For reinforced concrete beams, a 4% reduction in the loading capacity is found when these are subjected to freeze-thaw cycles and mixed corrosion only. However, if these actions are coupled with persistent loading, as expected during the service life of reinforced concrete structures in co...

1 March 2013 in Journal of Cold Regions Engineering
Verified
Journal Article
Closed access
BDBo Diao
Bo Diao
JZJian Zhang
Jian Zhang
YYYinghua Ye
Yinghua Ye
Shaohong ChengShaohong Cheng
Shaohong Cheng
The effects of freeze-thaw cycles and seawater corrosion on the material properties of air-entrained concrete specimens and structural behavior of reinforced air-entrained concrete beams under persistent loads were investigated in the laboratory. The air content of the specimens was designed to be 3.2 and 6.1%. Results show that when subjected to alternating actions of freeze-thaw cycles and seawater immersion, the compressive strength of concrete decreased when the number of freeze-thaw cycles increased, with the ones with higher air content showing better resistance to freeze-thaw attack. In the case of reinforced air-entrained concrete beam, the presence of persistent loads accelerated the structural behavior deterioration process. When the persistent load reached half of the ultimate load, the reduction of the ultimate load and ductility was found to be a couple of times greater than those without the persistent load. Compared to the beams with 3.2% air content, the yield load, the ultimate lo...

25 December 2016 in STRUCTURAL ENGINEERING AND MECHANICS
Verified
Journal Article
Closed access
SCShenggang Chen
Shenggang Chen
YYYinghua Ye
Yinghua Ye
QGQuanquan Guo
Quanquan Guo
Shaohong ChengShaohong Cheng
Shaohong Cheng
BDBo Diao
Bo Diao

1 January 2017 in Advances in Civil Engineering
Verified
Journal Article
Open access
PDF file
PFPapa Niane Faye
Papa Niane Faye
YYYinghua Ye
Yinghua Ye
BDBo Diao
Bo Diao
The importance of an accurate simulation of service conditions in the bond performance of reinforced concrete structures in coastal regions is highlighted. Four widths of initial crack of 0, 80, 150, and 210 microns were artificially made by inserting slice into bond specimens during concrete casting. Three bar diameters of 10 mm, 14 mm, and 18 mm were selected. At 28 days, the bond specimens were exposed to the environment of wet-dry cycles of seawater and atmosphere for another 90 days. The pull-out test was then conducted and chloride contents were tested at crack area along 40 mm depth. Results show that, for the specimen with 10 mm bar diameter, cracks width of less than 80 microns vanished rapidly during wet-dry cycles; for other specimens, cracks width of 100–150 microns decreased slightly. However the cracks of width more than 200 microns increased gradually; the chloride content decreased along the depth of concrete, and the chloride content increased as the widths of initial cracks increased or as the bar diameters increased. The ductility of bond specimens decreased as the diameter increased.

1 January 2018 in Advances in Civil Engineering
Verified
Journal Article
Open access
PDF file
JXJianchao Xu
Jianchao Xu
BDBo Diao
Bo Diao
QGQuanquan Guo
Quanquan Guo
YYYinghua Ye
Yinghua Ye
Y.L. MoY.L. Mo
Y.L. Mo
TZTianmin Zhou
Tianmin Zhou
Nowadays, U‐shaped thin‐walled concrete girders have been widely applied in the urban construction of rail viaducts in China as well as worldwide. However, the mixed torsional behaviors of these structures are not well understood. In this paper, the mixed torsional behaviors of the U‐shaped thin‐walled RC girders are theoretically analyzed, and a method predicting failure modes and ultimate torques is proposed. Nonlinear FE models based on ABAQUS to simulate the mixed torsional behaviors are built and calibrated with the test results. Parametric studies considering three crucial parameters (boundary condition, span length‐section height ratio, and ratio of longitudinal bars to stirrups) are conducted based on both the above suggested calculating method and the FE modeling. The calculated and the simulated results agree well with each other and with the test results. It is found that the failure modes of the U‐shaped thin‐walled RC girders under torsion are influenced by all the three parameters. Three kinds of failure modes are observed: flexural failures dominated by warping moment, shear failures caused by warping torque and circulatory torque, and flexural‐shear failures in the cases where flexural failure and shear failure appear almost at the same time.

1 January 2017 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
JWJieqiong Wu
Jieqiong Wu
BDBo Diao
Bo Diao
YYYinghua Ye
Yinghua Ye
XZXiaoning Zheng
Xiaoning Zheng
Effects of crack width, wet-dry ratio, and exposure duration of wet-dry cycles on chloride ingress of RC beams were experimentally studied. Crack widths of 40, 70, 90, and 120 microns were, respectively, induced by three-point flexural loading and four wet-dry ratios (seawater spraying 1 d in one wet-dry cycle) of 1 : 3, 1 : 7, 1 : 11, and 1 : 15 were selected. Chloride contents of RC beams were tested every 32 d (or 16 d) of wet-dry cycles. Results show that chloride content increased significantly when crack width was larger than 90 microns and wet-dry ratio was 1 : 3, and it increased slightly when crack width was 120 microns and wet-dry ratio was 1 : 7, 1 : 11, and 1 : 15. The chloride content on steel bar surface became the largest when crack width was less than 90 microns and wet-dry ratio was 1 : 7, and while crack width was equal to or greater than 90 microns and wet-dry ratio was 1 : 3, it was the largest. Based on the testing results, chloride diffusion model and prediction model of residual service life of RC beams were suggested considering combined effects of crack width and exposure duration. The predicted residual service lives were corresponding well with experimental results and they decreased as crack width increased.