In the analysis of petroleum hydrocarbon–contaminated soils for total petroleum hydrocarbons (TPHs) and polycyclic aromatic hydrocarbons (PAHs), the roles of spectroscopic and nonspectroscopic techniques are inseparable. Therefore, spectroscopic techniques cannot be discussed in isolation. In this report, spectroscopic techniques including Raman, fluorescence, infrared, and visible and near-infrared (Vis-NIR) spectroscopies, as well as mass spectroscopy (coupled to a gas chromatograph) and nonspectroscopic techniques such as gravimetry, immunoassay, and gas chromatography with flame ionization detection are reviewed. To bridge the perceived gap in coverage of the quantitative applications of Vis-NIR spectroscopy in the rapid determination of TPHs and PAHs in soils, a detailed review of studies from the period 1999–2012 are presented. This report also highlights the strengths and limitations of these techniques and evaluates their performance from the perspective of their attributes of general applicability, namely economic portability, operational time, accuracy, and occupational health and safety considerations. Overall, the fluorescence spectroscopic technique had the best performance (85% total score) in comparison to the others, and the gravimetric technique performed the least (60% total score). Method-specific solutions geared toward performance improvement are also suggested.
Visible and near‐infrared (VisNIR) spectroscopy is becoming recognised by soil scientists as a rapid and cost‐effective measurement method for hydrocarbons in petroleum‐contaminated soils. This study investigated the potential application of VisNIR spectroscopy (350–2500 nm) for the prediction of phenanthrene, a polycyclic aromatic hydrocarbon (PAH), in soils. A total of 150 diesel‐contaminated soil samples were used in the investigation. Partial least‐squares (PLS) regression analysis with full cross‐validation was used to develop models to predict the PAH compound. Results showed that the PAH compound was predicted well with residual prediction deviation of 2.0–2.32, root‐mean‐square error of prediction of 0.21–0.25 mg kg−1, and coefficient of determination (r2) of 0.75–0.83. The mechanism of prediction was attributed to covariation of the PAH with clay and soil organic carbon. Overall, the results demonstrated that the methodology may be used for predicting phenanthrene in soils utilizing the interrelationship between clay and soil organic carbon.
The reuse of solidified/stabilized low-temperature thermally desorbed (pre-treated) oil-based drill cuttings for construction purposes is becoming increasingly attractive in recent times; though, without screening a priori the levels of target residual organic contaminants against environmental guidelines to ensure compliance. In this study, pre-treated oil-based drill cuttings were collected from a waste treatment facility in the Niger Delta Province (5.317oN; 6.467oE), Nigeria and subjected to cement-based solidification/stabilization (S/S) followed by chemical leaching and screening of the data against local environmental guidelines. S/S was done with drill cuttings contents of 0 (control), 2, 4, 6, 8, and 10 % as part replacement for fine aggregate at 0.6:1, 0.65:1, 0.7:1, 0.75:1, and 0.8:1 water-to-cement ratios using 1:2:4 mix design for a grade-20 concrete. Afterwards, the surface microstructure, elemental composition, and unconfined compressive strength (UCS) of the solidified/stabilized matrix were determined. Amounts of heavy metals and total petroleum hydrocarbons (TPH) leached were also assessed. Results showed that the 2 % drill cuttings addition yielded the highest UCS (22.22-26.22 N/mm2) at water-to-cement ratio of 0.6:1, which were well above the recommended minimum UCS of 20 N/mm2 for a grade-20 concrete. The average amount of residual TPH in the solidified/stabilized matrix (62.41 mg/kg) was slightly higher than the local regulatory target value of 50 mg/kg; suggesting that the cement-based S/S failed to immobilize completely all the hydrocarbons in the pre-treated oil-based drill cuttings. This shows that the solidified/stabilized matrix is not in compliance with environmental guidelines on TPH for sustainable reuse as construction materials.