27 March 2019 in IEEE Transactions on Instrumentation and Measurement
We present in this paper a method and apparatus for nonintrusive measurement of active energy in low-voltage ac installations. In the proposed method, the active power is calculated from the voltage and current waveforms, and the phase shift between them. No voltage amplitude measurement is required since the nominal voltage of the ac installation is considered as the actual voltage. This approach bypasses the main disadvantage of capacitive ac voltage probing: low accuracy in amplitude measurements due to variations on the sensor coupling capacitance. The energy meter that implements the technique is composed of a commercial nonintrusive current sensor (clamp-on current transformer) and a contactless capacitive voltage sensor-designed to measure the voltage phase and waveform. The voltage sensor includes a shield to isolate it from external electric fields, making the energy meter suitable for applications in polyphase systems. The developed energy meter does not require on-site calibration, galvanic contact to the phase conductors, neither electrical circuit opening, allowing for quick, safe, and easy installation on overhead service drop line. Due to these characteristics, it can be used by electricity distribution companies in the preinspection of consumer units suspected of fraud. Experimental results proved that the developed energy meter is insensitive to the characteristics of cables (width and insulation), external electrical fields, as well as to the voltage sensor capacitance variations. The error of the active energy measurement under real condition in a two-phase installation was 1%.
16 September 2024 in IEEE Access
Weigh-In-Motion (WIM) systems dynamically measure vehicle weight, eliminating the need for vehicle stoppage on static scales. These systems are the most convenient way to identify overweight vehicles, one of the main causes of pavement damage. In order to be employed for direct enforcement, WIM systems must provide accurate and reliable measurements, which is very challenging, especially due to the dynamics of the moving vehicles. Aiming to overcome these challenges, various methods to estimate the weight of moving vehicles have been proposed. This paper first introduces a comprehensive overview of Weigh-In-Motion systems, addressing sensor types, road surface quality, weather conditions, and calibration methods. Moreover, the review addresses the impact of dynamic loads – oscillating forces exerted on the road surface by moving vehicles – on system accuracy, considering vehicle properties, speed, and road surface quality. The focus of this work are the different Weigh-In-Motion estimation methods, which were divided into two sequential stages: instantaneous axle load estimation and Gross Vehicle Weight (GVW) estimation. Although there is extensive research on WIM systems, comprehensive reviews that simultaneously categorize and explore both instantaneous axle load and GVW estimation techniques are lacking. By investigating these two sequential stages, this review highlights the limitations and challenges of implementing accurate WIM systems and indicates opportunities for further advances.
7 November 2019 in IEEE Photonics Technology Letters
30 May 2018 in Optics Letters
MSMarllon W. Schlischting
We propose and experimentally demonstrate a modulation technique for closed-loop interferometric fiber optic gyroscopes that improves its scale factor control and allows for the construction of gyroscopes with optimized angle random walk. The proposed two-level and two-period modulation is composed of two intercalated periods of the square wave modulation, one with amplitude of and the other with amplitude of . As in the two-level modulation, the angular velocity is obtained from the difference of consecutive output levels. Modulation depth error is obtained from the difference of the mean levels of the output from two consecutive periods. The proposed technique eliminates the limitation of square wave modulation: inefficient scale factor control at low angular velocities. Additionally, it requires a slower analog-to-digital converter than four-level modulation.
5 August 2015 in PRZEGLĄD ELEKTROTECHNICZNY
One of the most important design decisions in Non-Intrusive Load Monitoring (NILM) systems is choosing which electrical parameters will be used to define load signatures. In this paper, we present an experimental study where several electrical quantities of common home appliances were measured, in order to identify the most adequate to perform load disaggregation. It was found that active power, reactive power, rms voltage, and the first five odd harmonics of the current and voltage signals comprises the best set of parameters to define the signatures of residential loads. Streszczenie. W artykule zaprezentowano eksperymentalne studium w kt?rym zmierzono parametry typowych urz?dze? elektrycznych w celu okre?lenia i zestawienia obci??e?. Stwierdzono ?e moc czynna, moc bierna, napi?cie skuteczne i pierwsze pi?? nieparzystych harmonicznych pr?du mog? stanowi? podstaw? do prognozowania obci??e?. Badania parametr?w urz?dze? dla nieinwazyjnego monitorowania obci??e?. Keywords: load signature, power signature, non-intrusive load monitoring (NILM), harmonics. S?owa kluczowe: monitorowanie obci??e?, znaczniki obci??e?.. Introduction Over the last years, researches all around the world has been developing load monitoring systems, methodologies and algorithms to disaggregate the total energy consumption of a building. Despite the variety of techniques and technologies used, the disaggregation systems are divided in two main groups: intrusive and non-intrusive. Intrusive or decentralized systems, are those in which the power consumption is measured individually in each load. These systems are composed of several power meters, making them relatively expensive and difficult to install and maintain. The other way to disaggregate the energy consumption is through Non-Intrusive Load Monitoring (NILM). In this approach, only one power meter is required, usually installed at the utility service entrance. Systems which use the NILM methodology are chea