Martin Thomas Neukom

Martin Thomas Neukom

Auto-generated profile, based on publicly available information

Martin Thomas Neukom

Institute of Computational Physics , Zurich University of Applied Sciences , Wildbachstr. 21 , 8401 Winterthur , Switzerland

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 March 2018 in Science and Technology of Advanced Materials
Verified
Journal Article
Open access
MNMartin Neukom
Martin Neukom
SZSimon Züfle
Simon Züfle
SJSandra Jenatsch
Sandra Jenatsch
BRBeat Ruhstaller
Beat Ruhstaller
We present an overview of opto-electronic characterization techniques for solar cells including light-induced charge extraction by linearly increasing voltage, impedance spectroscopy, transient photovoltage, charge extraction and more. Guidelines for the interpretation of experimental results are derived based on charge drift-diffusion simulations of solar cells with common performance limitations. It is investigated how nonidealities like charge injection barriers, traps and low mobilities among others manifest themselves in each of the studied cell characterization techniques. Moreover, comprehensive parameter extraction for an organic bulk-heterojunction solar cell comprising PCDTBT:PC70BM is demonstrated. The simulations reproduce measured results of 9 different experimental techniques. Parameter correlation is minimized due to the combination of various techniques. Thereby a route to comprehensive and accurate parameter extraction is identified.

10 June 2019 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
MNMartin T. Neukom
Martin T. Neukom
ASAndreas Schiller
Andreas Schiller
SZSimon Züfle
Simon Züfle
EKEvelyne Knapp
Evelyne Knapp
JÁJorge Ávila
Jorge Ávila
BRBeat Ruhstaller
Beat Ruhstaller
A variety of experiments on vacuum-deposited methylammonium lead iodide perovskite solar cells are presented, including JV curves with different scan rates, light intensity-dependent open-circuit voltage, impedance spectra, intensity-modulated photocurrent spectra, transient photocurrents, and transient voltage step responses. All these experimental data sets are successfully reproduced by a charge drift-diffusion simulation model incorporating mobile ions and charge traps using a single set of parameters. While previous modeling studies focused on a single experimental technique, we combine steady-state, transient, and frequency-domain simulations and measurements. Our study is an important step toward quantitative simulation of perovskite solar cells, leading to a deeper understanding of the physical effects in these materials. The analysis of the transient current upon voltage turn-on in the dark reveals that the charge injection properties of the interfaces are triggered by the accumulation of mobile ionic defects. We show that the current rise of voltage step experiments allow for conclusions about the recombination at the interface. Whether one or two mobile ionic species are used in the model has only a minor influence on the observed effects. A delayed current rise observed upon reversing the bias from +3 to −3 V in the dark cannot be reproduced yet by our drift-diffusion model. We speculate that a reversible chemical reaction of mobile ions with the contact material may be the cause of this effect, thus requiring a future model extension. A parameter variation is performed in order to understand the performance-limiting factors of the device under investigation.

1 September 2017 in Solar Energy Materials and Solar Cells
Verified
Journal Article
Closed access
MNMartin Thomas Neukom
Martin Thomas Neukom
SZSimon Züfle
Simon Züfle
EKEvelyne Knapp
Evelyne Knapp
MMMohammed Makha
Mohammed Makha
RHRoland Hany
Roland Hany
BRBeat Ruhstaller
Beat Ruhstaller

1 June 2011 in Solar Energy
Verified
Journal Article
Closed access
MNM.T. Neukom
M.T. Neukom
NRN.A. Reinke
N.A. Reinke
BRB. Ruhstaller
B. Ruhstaller

1 December 2012 in Organic Electronics
Verified
Journal Article
Closed access
MNM.T. Neukom
M.T. Neukom
SZS. Züfle
S. Züfle
BRB. Ruhstaller
B. Ruhstaller

19 September 2017 in Journal of Applied Physics
Verified
Journal Article
Open access
SZS. Züfle
S. Züfle
SAS. Altazin
S. Altazin
AHA. Hofmann
A. Hofmann
LJL. Jäger
L. Jäger
MNM. T. Neukom
M. T. Neukom
BRB. Ruhstaller
B. Ruhstaller
Charge carrier transport in organic semiconductor devices is thermally activated with characteristic activation energies in the range of 0.2–0.6 eV, leading to strongly temperature-dependent behaviour. For designing efficient organic semiconductor materials and devices, it is therefore indispensable to understand the origin of these activation energies. We propose that in bilayer organic light-emitting diodes (OLEDs) employing a polar electron transport layer, as well as in metal-insulator-semiconductor (MIS) devices, the hole injection barrier Einj and the hole mobility activation energy Eμ can be decoupled from each other if temperature-dependent capacitance-frequency (C-f-T) and MIS-CELIV (charge extraction by linearly increasing voltage) experiments are combined. While the C-f-T signal contains information of both injection and transport, the CELIV current is expected to be insensitive to the electrode injection properties. We employ numerical drift-diffusion simulations to investigate the accuracy of this analytical parameter extraction approach and to develop criteria for its validity. We show that the implicit assumption of constant charge density and field profiles leads to systematic errors in determining the activation energies. Thus, one should be aware of the intrinsic limitations of the analytical Arrhenius fit, and for more accurate parameter determination a full drift-diffusion modelling is advised. Applying the analytical method to a standard bilayer OLED, we find that the total activation energy of 0.5 eV for the hole current can be split into contributions of ≈0.25 eV each for injection barrier and mobility. Finally, we also discuss the broader applicability of this method for other device stacks and material combinations.