7 June 2021 in IEEE Transactions on Neural Systems and Rehabilitation Engineering
Detecting human movement intentions is fundamental to neural control of robotic exoskeletons, as it is essential for achieving seamless transitions between different locomotion modes. In this study, we enhanced a muscle synergy-inspired method of locomotion mode identification by fusing the electromyography data with two types of data from wearable sensors (inertial measurement units), namely linear acceleration and angular velocity. From the finite state machine perspective, the enhanced method was used to systematically identify 2 static modes, 7 dynamic modes, and 27 transitions among them. In addition to the five broadly studied modes (level ground walking, ramps ascent/descent, stairs ascent/descent), we identified the transition between different walking speeds and modes of ramp walking at different inclination angles. Seven combinations of sensor fusion were conducted, on experimental data from 8 able-bodied adult subjects, and their classification accuracy and prediction time were compared. Prediction based on a fusion of electromyography and gyroscope (angular velocity) data predicted transitions earlier and with higher accuracy. All transitions and modes were identified with a total average classification accuracy of 94.5% with fused sensor data. For nearly all transitions, we were able to predict the next locomotion mode 300-500ms prior to the step into that mode.
21 September 2022 in IEEE Transactions on Biomedical Engineering
There is an increasing demand for accurately predicting human movement intentions. To be effective, predictions must be performed as early as possible in the preceding step, though precisely how early has been studied relatively little; how and when a person's movement patterns in a transition step deviate from those in the preceding step must be clearly defined. In this study, we collected motion kinematics, kinetics and electromyography data from 9 able-bodied participants during 7 locomotion modes. Twelve types of steps between the 7 locomotion modes were studied, including 5 continuous steps (taking another step in the same locomotion mode) and 7 transitions steps (taking a step from one locomotion mode into another). For each joint degree of freedom, joint angles, angular velocities, moments, and moment rates were compared between continuous steps and transition steps, and the relative timing during the transition step at which these parameters diverged from those of a continuous step, which we refer to as transition starting times, were identified using multiple analyses of variance. Muscle synergies were also extracted for each step, and we studied in which locomotion modes these synergies were common (task-shared) and in which modes they were specific (task-specific). The transition starting times varied among different transitions and joint degrees of freedom. Most transitions started in the swing phase of the transition step. These findings can be applied to determine the critical timing at which a powered assistive device must adapt its control to enable safe and comfortable support to a user.
23 June 2021 in IEEE Access
Lower extremity powered exoskeletons help people with movement disorders to perform daily activities and are used increasingly in gait retraining and rehabilitation. Studies of powered exoskeletons often focus on technological aspects such as actuators, control methods, energy and effects on gait. Limited research has been conducted on how different mechanical design parameters can affect the user. In this paper, we study the effects of weight distributions of knee exoskeleton components on simulated muscle activities during three functional movements. Four knee exoskeleton CAD models were developed based on actual motor and gear reducer products. Different placements of the motor and gearbox resulted in different weight distributions. One unilateral knee exoskeleton prototype was fabricated and tested on 5 healthy subjects. Simulation results were compared to observed electromyography signals. Muscle activities varied among weight distributions and movements, wherein no one physical design was optimal for all movements. We describe how a powered exoskeleton's core components can be expected to affect a user's ability and performance. Exoskeleton physical design should ideally take the user's activity goals and ability into consideration.
23 December 2015 in Frontiers of Physics
Decane is one of the volatile organic compounds (VOCs) in human breath. Successful detection of decane in human breath has vast prospects for early lung cancer diagnosis. In this paper, a novel detecting device based on a filter surface acoustic wave (SAW) gas sensor is presented. SAW sensors coated with a thin oxidized graphene film were used to detect decane in parts per million (ppm) concentrations. Control and signal detection circuits were designed using a vector network analyzer with a detection resolution of insertion loss down to 0.0001 dB. The results showed that the SAW sensor could respond quickly with great sensitivity when exposed to 0.2 ppm decane. This device shows tremendous potential in medical diagnosis and environmental assessment.
10 July 2025 in IEEE Robotics and Automation Letters
Wearable robotic exoskeletons are frequently explored for their efficacy in physical rehabilitation and for assistance in daily activities in people with motor disorders, yet relatively few have convincing evidence for use. The concept of human-in-the-loop optimization has been used to identify ideal exoskeleton assistive torques based on measured individual performance metrics, whereas few studies report optimizing several performance metrics simultaneously. In this study, we propose a multi-objective human-in-the-loop optimization that adjusts exoskeleton assistive profiles to improve several gait quality measures, specifically foot segment kinematics and step length symmetry. A preliminary proof-of-concept evaluation was conducted with five non-disabled participants, where a weighted shoe was used to simulate the gait deviations associated with dropfoot and excessive inversion. The gait quality metrics improved more for each new generation. With optimal assistive solutions, foot segment kinematics improved (10 mm higher foot clearance height and a 7$^{\circ }$ increase in inclination angle) and step length became more symmetric (asymmetry reduced from 9% to 2%), compared to simulated impairment. Within this set of solutions, each represents a unique balance between the two objectives, wherein a solution that prioritized normalizing step length symmetry could slightly sacrifice normalizing foot segment kinematics, and vice versa. By taking advantage of the trade-off relationship between the two objectives, more flexible, individualized, and situation-dependent assistance can be obtained. These results demonstrate the method's usefulness in determining subject-specific exoskeleton control parameters that improve several measures of gait. Future applications include refining this protocol for actual dropfoot, offering personalized assistance to restore their functional mobility and reduce compensatory movements, and validating its long-term effects.