The Eastern Rift System (ERS) of northern Tanzania and southern Kenya, where a cratonic lithosphere is in the early stages of rifting, offers an ideal venue for investigating the roles of magma and other fluids in such an environment. To illuminate these roles, we jointly invert arrival times of locally recorded P and S body waves, phase delays of ambient noise generated Rayleigh waves and Bouguer anomalies from gravity observations to generate a 3-D image of P and S wave speeds in the upper 25 km of the crust. While joint inversion of gravity and arrival times requires a relationship between density and wave speeds, the improvement in resolution obtained by the combination of these disparate data sets serves to further constrain models, and reduce uncertainties. The most significant features in the 3-D model are (1) P and S wave speeds that are 10–15 per cent lower beneath the rift zone than in the surrounding regions, (2) a relatively high wave speed tabular feature located along the western edge of the Natron and Manyara rifts, and (3) low (∼1.71) values of Vp/Vs throughout the upper crust, with the lowest ratios along the boundaries of the rift zones. The low P and S wave speeds at mid-crustal levels beneath the rift valley are an expected consequence of active volcanism, and the tabular, high-wave speed feature is interpreted to be an uplifted footwall at the western edge of the rift. Given the high levels of CO2 outgassing observed at the surface along border fault zones, and the sensitivity of Vp/Vs to pore-fluid compressibility, we infer that the low Vp/Vs values in and around the rift zone are caused by the volcanic plumbing in the upper crust being suffused by a gaseous CO2 froth on top of a deeper, crystalline mush. The repository for molten rock is likely located in the lower crust and upper mantle, where the Vp/Vs ratios are significantly higher.
4 September 2016 in Geophysical Journal International
We use seismic tomography to investigate the state of the supraslab mantle beneath northern Chile, a part of the Nazca-South America Plate boundary known for frequent megathrust earthquakes and active volcanism. We performed a joint inversion of arrival times from earthquake generated body waves and phase delay times from ambient noise generated surface waves recorded by a combined 360 seismic stations deployed in northern Chile at various times over several decades. Our preferred model shows an increase in Vp/Vs by as much as 3 per cent from the subducting slab into the supraslab mantle throughout northern Chile. Combined with low values of both Vp and Vs at depths between 40 and 80 km, we attribute this increase in Vp/Vs to the serpentinization of the supraslab mantle in this depth range. The region of high Vp/Vs extends to 80–120 km depth within the supraslab mantle, but Vp and Vs both increase to normal to high values. This combination, along with the greater abundance of ambient seismicity and higher temperatures at these depths, suggest that conversion from basalt to eclogite in the slab accelerates and that the fluids expelled into the supraslab mantle contribute to partial melt. The corresponding maximum melt fraction is estimated to be about 1 per cent. Both the volume of the region affected by hydration and size of the wave speed contrasts are significantly larger north of ∼21°S. This latitude also delimits large coastal scarps and the eruption of ignimbrites in the north. Ambient seismicity is more abundant north of 21°S, and the seismic zone south of this latitude is offset to the east. The high Vp/Vs region in the north may extend along the slab interface to depths as shallow as 20 km, where it corresponds to a region of reduced seismic coupling and overlaps the rupture zone of the recent 2014 M8.2 Pisagua earthquake. A potential cause of these contrasts is enhanced hydration of the subducting oceanic lithosphere related to a string of seamounts located on the Iquique Ridge of the Nazca Plate.
The 14 November 2016 Mw7.8 Kaikōura earthquake in the northern South Island, New Zealand, involved highly complex, multifault rupture. We combine data from a temporary network and the permanent national seismograph network to repick and relocate ~2,700 aftershocks of M≥3 that occurred between 14 November 2016 and 13 May 2017. Automatic phase‐picking is carried out using REST, a newly developed hybrid method whose pick quality is assessed by comparing automatic picks for a subset of 138 events with analysts' picks. Aftershock hypocenters computed from high‐quality REST picks and a 3‐D velocity model cluster almost exclusively in the shallow crust of the upper plate and reveal linkages at depth between surface‐rupturing fault segments. Only eight aftershocks are relocated on a deeper structure positioned between patches of geodetically detected afterslip. This indicates that afterslip has not triggered significant earthquake activity on the subduction interface during the period of aftershock activity analyzed.
We adapt a 2-D spectral domain finite difference waveform tomography algorithm previously used in active source seismological imaging to the case of a plane wave propagating through a 2.5-D viscoelastic medium in order to recover P and S wave speed variations from body waves recorded at teleseismic distances. A transferable efficacy that permits recovery of arbitrarily heterogenous models on moderately sized computers provides the primary motivation for choosing this algorithm. Synthetic waveforms can be generated either by specifying an analytic solution for a background plane wave in a 1-D model and solving for the source distribution that would produce it, or by solving for a scattered field excited by a plane wave source and then adding the background wavefield to it. Because the former approach typically involves a concentration of sources at the free surface, the latter tends to be more stable numerically. We adapt a gradient approach to solve the inverse problem to maintain tractability; calculating the gradient does not require much more computational effort than does the forward problem. The waveform tomography algorithm can be applied in a straightforward way to perform receiver function migration and traveltime inversion.