1 August 2004 in International Journal of Clothing Science and Technology
This paper reports an experimental investigation into the effect of laundering on seam tensile properties with the variation of stitch density, linear density of sewing threads and composition of base material. Tensile properties such as initial modulus, secant modulus, seam strength, strain at fracture and work up to fracture increase with stitch and linear density of sewing threads. The impact of coarser yarn is greater on seam properties of polyester‐cotton fabric than cotton fabric. The tensile properties except seam strain are reduced due to laundering. Reduction in initial modulus and secant modulus due to laundering is higher for polyester‐cotton fabric whereas decrease in seam strength, seam efficiency and strain at break is greater for coarser sewing thread.
4 June 2018 in Research Journal of Textile and Apparel
Purpose: The purpose of this review paper is to define the dominating factors (such as fiber, yarn, fabric structure, sewing thread, sewing needle and machine parameters) that affect the seam damages and causing defects. It also describes the various explanations of sewing defects in garment production and critically analyzes them for optimum selection of parameters and speeds for minimizing such faults. Hence, the knowledge of various factors which affect the sewing damages/defects will be helpful for garment manufacturers/researchers to know influence of the parameters and control the quality of producing seam.Design/methodology/approach: This section is not applicable for a review paper.Findings: Sewing damages such as needle cut and other sewing damages/defects are studied mostly in woven fabric. There are very few studies conducted on knitted fabric sewing damages/defects. The sewing damage problems do not have single solution that is capable of removing these damages in fabric. All the determined and affecting parameters related to fiber, yarn, fabric construction, sewing thread and sewing machine must be examined to design appropriate remedial measurement related to machine design, fabric parameters and sewing thread. This could help in minimizing or eliminating the needle cut and other sewing damage problems.Originality/value: It is an original review work and is helpful for garment manufacturers/researchers to reduce the defects and be able to produce good quality seam.
1 August 2008 in Journal of Tissue Viability
1 June 2022 in Journal of Industrial Textiles
Textiles play a vital role in assuring the thermal stability of the human body. The absorption of perspiration or moisture from a humid environment might result in wet clothing. Protective and sports apparel are often wet when the wearer is involved in high level of activity; thereby affecting the comfort. In order to understand the comfort behaviour of textiles in wet state, most of the researchers used the distilled water or NaCl aqueous solution. However, human sweat is a very complex aqueous mixture of chemicals comprising of salts, lipids, urea, lactic acid, carbohydrates, and minerals. In the present study, the effect of simulated sweat solution on the thermal behaviour of multi-layered fabric assembly is studied and compared with that of distilled water. The multi-layered fabric assembly consists of breathable PU-coated nylon as an outer layer; polyester knitted fabric as an inner layer; and micro-polyester wadding/hollow-polyester wadding/spacer fabric as the middle layer. In addition, the inner layer (next to the skin) is also tested for thermal comfort for both dry and wet states. It is observed that thermal properties of fabrics are drastically affected under wet conditions. The inner layer of fabric wetted with distilled water shows higher thermal conductivity as compared to that wetted with simulated sweat. Among various multi-layered assemblies, the thermal resistance and thermal diffusion of multi-layered assembly having hollow polyester wadding as a middle layer is high as compared to that having spacer fabric in the middle, under both dry and wet conditions.
1 June 2016 in Medical Engineering & Physics
The effectiveness of the compression treatment by a medical compression bandage is dependent on the pressure generated at the interface between the bandage and the skin. This pressure is called interface pressure or sub-bandage pressure. The performance of a bandage depends upon the level of interface pressure applied by the bandage and the sustenance of this pressure over time. The interface pressure exerted by the bandage depends on several other factors like limb shape or size, application technique, physical and structural properties of the bandage, physical activities taken by the patient, etc. The current understanding of how bandages apply pressure to a limb is based on the Law of Laplace, which states that tension in the walls of a container is dependent on both the pressure of the container's content and its radius. This concept was translated mathematically into equation relating pressure to tension and radius by Thomas. In addition, a modified equation was generated by multiplying the model with a constant that represents the number of bandage layers in order to use the model to estimate the pressure applied by multi-layer bandages. This simple multiplication adjustment was questioned by researchers. They had doubts about the model validity and whether it can be used to predict the sub-bandage pressure applied by pressure garments. One of the questions that were raised regarding the bandage thickness affecting the sub-bandage pressure has been recently explored by Al Khaburi where he used the thin and thick cylinder shell theory to study the effect of Multi Component Bandage's (MCB) thickness on the sub-bandage pressure. The model by Al Khaburi and the earlier models developed for pressure prediction are all based on calculations considering the cylindrical limb shapes although the human limb normally is wider at the calf and reduces in circumference towards the ankle. So in our approach, the bandage is assumed to take a conical shape during application and membrane shell theory is used for developing pressure prediction model for multi-layers of bandage. Both analytical and experimental work showed that the effect of bandage thickness and the geometry of the limb on pressure produced by multi-layers of bandage are significant. The model developed when compared to the data obtained using experimental setup confirmed the validity of the mathematical model for multi-layers of bandage based on conical geometry of the limb.
31 August 2014 in Fibers and Polymers