Inkjet printing is a cost-effective and scalable way to assemble colloidal materials into desired patterns in a vacuum- and lithography-free manner. Two-dimensional (2D) nanosheets are a promising material category for printed electronics because of their compatibility with solution processing for stable ink formulations as well as a wide range of electronic types from metal, semiconductor to insulator. Furthermore, their dangling bond-free surface enables atomically thin, electronically-active thin films with van der Waals contacts which significantly reduce the junction resistance. Here, we demonstrate all inkjet-printed thin-film transistors consisting of electrochemically exfoliated graphene, MoS2, and HfO2 as metallic electrodes, a semiconducting channel, and a high-k dielectric layer, respectively. In particular, the HfO2 dielectric layer is prepared via two-step; electrochemical exfoliation of semiconducting HfS2 followed by a thermal oxidation process to overcome the incompatibility of electrochemical exfoliation with insulating crystals. Consequently, all inkjet-printed 2D nanosheets with various electronic types enable high-performance, thin-film transistors which demonstrate field-effect mobilities and current on/off ratios of ~10 cm2 V−1 s−1 and >105, respectively, at low operating voltage.
Two-dimensional (2D) black phosphorus (BP), or phosphorene, has recently emerged as a promising 2D semiconductor because of its p-type charge transport behavior and near-infrared photoresponsivity. However, the application of BP in practical electronic and optoelectronic devices is hindered by challenges in producing high-quality BP films over large areas. In this manuscript, we present a facile solution-based process to create wafer-scale BP films for fabrication of p-channel field-effect transistors that are responsive to near infrared light. Few-layer BP nanosheets are first exfoliated from the bulk crystal via electrochemical intercalation of cationic molecules and then vacuum-filtered through an anodic aluminum oxide membrane. The resulting BP film can be transferred onto an SiO2-coated silicon substrate, thereby allowing for realization of field-effect transistors after electrode deposition and thermal annealing. The transistor array exhibits spatial uniformity in electrical performance with an average hole mobility of ~0.002 cm2 V−1 s−1 and on/off ratio of 130. Furthermore, gate-induced modulation of the BP channel allows for enhancement in the photoresponsivity for 1550-nm light illumination up to 24 mA W−1, which benefits the application of the phototransistor array for near infrared imaging.
Solution-based processing of two-dimensional (2D) materials has garnered significant interest as a facile and versatile route for the large-scalable production of 2D material films. Despite the benefits in process, these films were not considered suitable for device applications during the early stages of research because their electronic properties were far from those of 2D materials obtained through micromechanical exfoliation or chemical vapor deposition. Due to the small lateral dimensions and polydisperse thickness of constituent 2D nanosheets, the resulting film tends to be porous and exhibits numerous inter-sheet junctions, primarily contacting edge-to-edge. This nanosheet morphology leads to poor electrical conductivity of the network, and also hinders the film functioning as a semiconductor or an insulator. To produce ultrathin 2D nanosheets with narrow thickness distribution and large lateral sizes, various chemical exfoliation strategies have been explored, but these are limited by long process times, involvement of harsh chemicals, and/or undesired structural damage or phase changes. Recent breakthroughs in electrochemical exfoliation using tetraalkylammonium intercalants enabled the production of high-quality 2D nanosheets with structural characteristics favorable for producing ultrathin, conformal films of 2D materials, which allow for scalable production of high-performance electronic components that can readily be assembled into functional devices via solution-processing. In this review article, we aim to offer an extensive introduction solution-based processing techniques for acquiring 2D nanosheets, their subsequent assembly into thin films, and their diverse applications, primarily focusing on electronics and optoelectronics but also extending to other fields. Remaining challenges and potential avenues for advancement will also be discussed.
Reconfigurable devices have garnered significant attention for alleviating the scaling requirements of conventional complementary metal-oxide-semiconductor technology by reducing the number of components needed to construct functional circuits. Prior work required continuous voltage application to programming gate terminal(s) alongside the primary gate, undermining the advantages of reconfigurable devices in achieving compact and power-efficient integrated circuits. Here, we realize scalable reconfigurable devices based on single-gate field-effect transistors that integrate highly aligned single-walled carbon nanotube channels with a ferroelectric aluminum scandium nitride gate dielectric. The devices exhibit ambipolar characteristics with high, well-balanced on-state currents (~270 μA μm−1 at a drain voltage of 3 V) and on/off ratios exceeding 105, along with large memory windows and excellent retention behavior. Ferroelectric polarization switching also enables reconfiguration between p- and n-channel transistors, allowing ternary content-addressable memory to be realized with far fewer devices than circuits based on conventional silicon technology or alternative memory devices.