Xuedong Bai

Xuedong Bai

Auto-generated profile, based on publicly available information

Xuedong Bai

Dental Materials Science, Applied Oral Sciences and Community Dental Care, Faculty of Dentistry, The University of Hong Kong, Hong Kong SAR, PR China

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 December 2025 in Journal of Dentistry
Verified
Journal Article
Closed access
XBXuedong Bai
Xuedong Bai
MXMengxiao Xu
Mengxiao Xu
AWAnqi Wang
Anqi Wang
Yanning ChenYanning Chen
Yanning Chen
EPEdmond Pow
Edmond Pow
James Kit Hon TsoiJames Kit Hon Tsoi
James Kit Hon Tsoi

22 September 2025 in Journal of Dentistry
Verified
Journal Article
Closed access
SCShujiang Chen
Shujiang Chen
CKChun Yin Kam
Chun Yin Kam
YLYun Hong Lee
Yun Hong Lee
XBXuedong Bai
Xuedong Bai
Yanning ChenYanning Chen
Yanning Chen
James Kit Hon TsoiJames Kit Hon Tsoi
James Kit Hon Tsoi

25 June 2026 in Dental Materials
Verified
Journal Article
Open access
Yanning ChenYanning Chen
Yanning Chen
HDHao Ding
Hao Ding
QLQianhui Li
Qianhui Li
SCShujiang Chen
Shujiang Chen
XBXuedong Bai
Xuedong Bai
James Kit Hon TsoiJames Kit Hon Tsoi
James Kit Hon Tsoi
This study aimed to investigate the fatigue behaviour of direct and CAD/CAM indirect restorative materials cemented to a dentine analogue substrate. Two resin-based direct restorative materials (G-ænial Universal Injectable, GU; Filtek Supreme Flowable Restorative, FS), and two CAD/CAM indirect restorative materials (IPS e.max CAD, EM; Tetric CAD, TE), were tested. Flexural properties (flexural strength and flexural modulus) and energy dissipation parameters (modulus of toughness, elastic recovery, and their difference) were determined via the three-point bending (3PB) test (n = 10). After the monotonic pilot trial, the wet cyclic fatigue test was performed following the staircase approach (initial load: approx. 40% of the monotonic load; step size: approx. 5% of the monotonic load; 500,000 cycles per specimen; 20 Hz; n = 15). Mean fatigue failure load (FFL), standard deviation (SD), and 95% confidence interval (CI) were calculated using the Dixon and Mood method. FFLs were also evaluated with Weibull statistics. Specimen survival or failure was examined visually and under a stereomicroscope, then fractographic analysis were conducted on sectioned specimens under the SEM. Finite Element Analysis (FEA) was performed using the mean FFLs and 300 N axial load on tri-layer models, respectively. SPSS 26.0 was used for statistical analysis and the significant level was pre-set as α = 0.05. EM showed significantly higher flexural strength and elastic modulus than the three resin-based composites (RBCs) (p < 0.001). Nevertheless, three energy dissipation parameters of RBCs were significantly higher than those of lithium disilicate, ranking TE > FS > GU > EM. The mean FFL showed a similar trend, ranking TE (353.93 ± 43.01 N) > GU (276.79 ± 34.24 N) > FS (255.33 ± 47.30 N) > EM (184.00 ± 76.92 N). EM presented the lowest Weibull parameters and the highest RSD values, while TE presented superior fatigue resistance and structural reliability. Distinct failure characteristics and stress distribution patterns between EM and three resin-matrix materials were found. Distinct fatigue behaviours were discovered between lithium disilicate and resin-based materials, including the fatigue failure load, failure mode, and stress distribution pattern. Resin-based composites outperformed lithium disilicate in the cyclic fatigue test, among which the CAD/CAM indirect RBC material performed the best fatigue resistance. Energy dissipation parameters may serve as preliminary predictors to the fatigue properties.

6 August 2026 in Dental Materials
Verified
Journal Article
Closed access
SHShiqian Huang
Shiqian Huang
DYDing Yuan
Ding Yuan
MXMengxiao Xu
Mengxiao Xu
XBXuedong Bai
Xuedong Bai
CYChau Tin Yuet
Chau Tin Yuet
XLXin Li
Xin Li