We present a metamaterial absorber detector array that enables room-temperature, narrow-band detection of gigahertz (GHz) radiation in the band (2–4 GHz). The system is implemented in a commercial printed circuit board process and we characterize the detector sensitivity and angular dependence. A modified metamaterial absorber geometry allows for each unit cell to act as an isolated detector pixel and to collectively form a focal plane array . Each pixel can have a dedicated microwave receiver chain and functions together as a hybrid device tuned to maximize the efficiency of detected power. The demonstrated subwavelength pixel shows detected sensitivity of , corresponding to a radiation power density of , with pixel to pixel coupling interference below at 2.5 GHz.
In this article, we propose and demonstrate a spectrum-to-space mapping principle for localizing multiple wireless nodes in a simultaneous and single-shot fashion at terahertz (THz) frequencies. Spectrum-to-space mapping is achieved through two dual-port chip integrated waveguide (CIW)-based leaky-wave antennas (LWAs). Interfacing with the two LWAs, we integrate two transmitting and receiving chains operating between 360- and 400-GHz range in a single chip realized in a 65-nm bulk CMOS process. Utilizing the carefully engineered dispersive nature of the LWA and its frequency-dependent radiation patterns, we create unique spectrum-to-space calibration maps for both 1-D and 2-D angular localizations. The measured one-shot localization error variance is less than 1° in 1-D space with 200-Hz-resolution bandwidth (BW) and less than 2° in 2-D space for a 20-Hz-resolution BW. The high-resolution nature of the localization principle in a single-shot fashion makes this approach attractive for multi-wireless node localization, link discovery, beam-forming, beam-management, and beam-optimization methods.
Security in wireless networks has traditionally been addressed above the physical layer. With the expected proliferation of applications in 5G, the mm-wave spectrum and new network architectures, traditional methods of data encryption may not be scalable for energy-constrained applications. Thus, there has been a surge of interest in physical layer security that aims to impart confidentiality by exploiting the physics of the wireless communication channel without the need for exchanging secret cryptographic keys [1], [2]. The idea of a secure directional wireless link between a TX/RX pair is to preserve the signal information within a secure cone where the intended receiver is located while scrambling signals everywhere else to prevent eavesdropping. In a phased array, the same temporal digital information is fed to all the TX elements, transmitting the same information to all directions albeit at different power levels. This information can be recovered (especially at the side lobes) with a sensitive enough receiver. Spatial modulation with I, Q radiated out through separate antennas, and modulation of parasitic elements can distort the constellation in other directions [3], [4]. However, this one-to-one (bijective) mapping allows potential decoding by the eavesdropper, particularly using various signal processing and machine-learning-based classification techniques. Time modulation in an antenna array can incorporate such physical layer security through careful mapping of symbols to antennas in a time-modulated fashion.
Integrated high-power THz arrays with beamforming ability can enable new applications in communication, sensing, imaging, and spectroscopy [1]. However, due to the limited power-generation capability of a single source above the device f max [2], efficient spatial power combining from multiple coherent sources becomes necessary to generate mW level of power. To create this 2D array of distributed frequency and phase-locked sources, prior works have shown central LO-signal distribution with local harmonic upconversion [3]. However, this requires high power consumption in the LO distribution. In addition, phase-matching with PVT variations across the sources at the harmonic-radiating THz frequency can be quite challenging. A small ∆θ perturbation at the fundamental frequency translates to N∆θ at the radiated N th harmonic, thus corrupting the array beam pattern. Another method to synchronize multiple distributed radiating sources (ƛ/2 spaced at Nfo) is through a mutual coupling network with active/passive elements in a coupled oscillator array [4], [5]. However, the locking range in these methods is typically narrow (∆f locking ~ f 0 /20 to f 0 /10) and PVT variations can easily cause desynchronization. In such a network, each cell is a self-sustaining oscillator, and the coupling network tries to establish injection signals to force synchronization between these individual free-running oscillators. In this paper, we used a 2D oscillating network with negative G m (–G m ) cells at each node that do not oscillate individually but only collectively, establishing a robust frequency and phase distribution network across the chip for high THz-power generation. By making this network as the lowest layer, we can now separate the locking mechanism and the power-generation sources. This avoids loading and sub-optimal operation of the power sources. The distributed oscillating network at the lowest layer operates at 69.3GHz, and multi-layer local harmonic generation produces a radiated power of −3dBm and +14dBm EIRP at 416GHz in a 4×4 array.