15 February 2024 in ISIJ International
In the sintering process, productivity and strength are essential indicators, and it is known that they are closely related to the sintering time and temperature. Since the sintering time and high temperature holding time vary greatly depending on the combustion behavior of coke breeze, various studies have been conducted on the influence of oxygen, which is a critical element in sintering phenomena. However, the influence of oxygen enrichment on sinter strength and yield has not yet been unified. In this study, sintering productivity, strength and yield were investigated when the oxygen concentration of the inlet gas was increased to 40 vol%. In addition, the heat profile of pot tests and the effect of the oxygen partial pressure on the melting property were analyzed from the viewpoint of thermodynamics. As a result, it was found that yield showed the maximum value at 30 vol%-O2 and strength increased with oxygen enrichment. As for yield, it was found that the effect of the heat profile was significant, and deviation between the heat transfer speed and the combustion speed started when the oxygen concentration exceeded 30 vol%. Regarding strength, it was suggested that strength improvement was caused by the increase in the amount of melt produced by oxygen enrichment in addition to the effect of the high temperature holding time.
15 July 2022 in ISIJ International
For countermeasures of deterioration in iron ore, development of pretreatment technology for high quality iron ore fine is critical issue in the sintering process. However with increasing small particles, sinter productivity is decreased by lower permeability due to increment of un-granulated particles or considerably large granules. Therefore understanding of granulation phenomena becomes more important issue. Since moisture of iron ore largely relates to the granulation behavior, it is necessary to reveal the effect of moisture on granulation rate for controlling the process. In this study, granulation tests were performed and the size distribution of granule was analyzed with probability model and new model considering granulation rate. Based on the calculation results, the effect of moisture on granulation rate was discussed.
15 August 2025 in Tetsu-to-Hagane
The reduction disintegration index (RDI) of sintered ore, which is the main raw material of blast furnaces, greatly affects blast furnace operation. In order to improve RDI without deteriorating the reducibility index (RI), sintered ore having a CaO concentration of 20 mass%, which is higher than the conventional 10 mass% when using porous Australian iron ore, was produced, and its effects on the mineral structure, porosity, RI and RDI were evaluated. In the sintered ore having a CaO concentration of 20 mass%, hematite decreased and calcium-ferrite (sum of other component system calcium-ferrite and binary calcium-ferrite), the SFCA-I/SFCA ratio and porosity increased in comparison with that having a CaO concentration of 10 mass%. When Australian iron ore was used as a raw material for sintered ore, RI increased in sintered ore having a CaO concentration of 20 mass% compared with the one having a CaO concentration of 10 mass%. In addition, RDI was improved in the sintered ore having a CaO concentration of 20 mass% compared with the that having a CaO concentration of 10 mass%. This is due to the formation of binary calcium-ferrite instead of secondary hematite, which deteriorates RDI.
15 October 2023 in ISIJ International
To reduce the reducing agent ratio and CO2 emissions in blast furnace operation, it is important to control the material structure of sintered ore, which affects its metallurgical and mechanical properties. Multicomponent calcium ferrites (also called CF or SFCA (silico-ferrite of calcium and aluminum)), which is a type of melting and solidification structure, has attracted considerable interest recently, and the chemical composition and crystal structure of each CF have been researched. Although the crystal structure of CF has conventionally been analyzed mainly by XRD, the atomic arrangement could not be observed directly. Therefore, in this study, CF was investigated at the atomic level by scanning transmission electron microscopy (STEM). This research revealed that acicular CF, which was previously understood to be SFCA-I, has a SFCA (≠ SFCA-I) structure. It was also found that columnar CF had a non-periodic SFCA structure induced with a magnetite-like structure. Furthermore, a CF in which SFCA and SFCA-I were alternately stacked repeatedly was also discovered. This research clarified the fact that CF has a non-periodic structure at the atomic level.
1 January 2023 in Tetsu-to-Hagane
In the sintering process, productivity and strength are essential indicators, and it is known that they are closely related to the sintering time and temperature. Since the sintering time and high temperature holding time vary greatly depending on the combustion behavior of coke breeze, various studies have been conducted on the influence of oxygen which is critical element in the sintering phenomena. However, the influence of oxygen enrichment on sinter strength and yield has not yet been unified. In this study, the sintering productivity, strength, and yield were investigated when the oxygen concentration of the inlet gas was increased to 40 vol%. In addition, the heat profile on pot tests and the effect of oxygen partial pressure on the melting property were analyzed from the viewpoint of thermodynamics. As a result, it was found that the yield showed the maximum value at 30 vol% oxygen concentration, and the strength increased with oxygen enrichment. As for the yield, it was found that the effect of the heat profile was significant, and the deviation between the heat transfer speed and the combustion speed started when the oxygen concentration exceeded 30 vol%. On the other hand, it was suggested that the strength improvement was caused by the increase in the amount of melt produced by oxygen enrichment in addition to the effect of high temperature holding time.
1 January 2021 in Tetsu-to-Hagane
For countermeasures of deterioration in iron ore, development of pretreatment technology for high quality iron ore fine is critical issue in the sintering process. However with increasing fine particles, sinter productivity is decreased by decreasing permeability due to increment of un-granulated particles or considerably large granules. Therefore understanding of granulation phenomena becomes more important issue. Since a moisture of iron ore largely relates to the granulation behavior, it is necessary to reveal the effect of moisture on granulation rate for controlling the process. In this study, granulation tests were performed and the size distribution of granule was analyzed with probability model and new model considering granulation rate. Based on the calculation results, the effect of moisture on granulation rate was discussed.