Mladen Knezic

Mladen Knezic

Auto-generated profile, based on publicly available information

Mladen Knezic

Faculty of Electrical Engineering, University of Banja Luka, Bosnia and Herzegovina

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2011
Verified
Conference Paper
Closed access
ZIZeljko Ivanovic
Zeljko Ivanovic
BBBranko Blanusa
Branko Blanusa
MKMladen Knezic
Mladen Knezic
The analytical expressions for boost converter loss are presented in this paper. All significant sources of conduction and dynamic losses within the converter elements, including losses in choke magnetic material and switching losses which occur due to diode recovery time, are discussed. Sources of losses in continuous and discontinuous current mode of converter are examined. The equivalent input resistance of the generator is included in converter loss model. In the paper, the case when single-phase rectifier is input circuit of the converter is presented. Loss model of converter and its efficiency was compared with experimental measurements on a prototype of the boost converter.

1 September 2017
Verified
Conference Paper
Closed access
IÁInés Álvarez
Inés Álvarez
JPJulián Proenza
Julián Proenza
MBManuel Barranco
Manuel Barranco
MKMladen Knezic
Mladen Knezic
Time-Sensitive Networking (TSN) is a set of technical standards that is being developed to provide Ethernet with hard real-time, reliability and flexibility services. In the last years, there has been a growing interest in increasing the connectivity of all kind of devices. This trend has reached industrial environments, where the demanding timing and reliability constraints imposed the use of specialised networks with specific features to support these requirements. Moreover, the industry has shown interest in using Ethernet as the network technology in industrial environments, due to its low cost, high bandwidth and extensive use. The ability of TSN to support both, data-oriented and traditional control traffic over the same network makes it an appealing technology to implement the next generation of industrial networks with high connectivity. Nevertheless, TSN does not cover some reliability aspects important for its deployment in critical systems. In this work we propose the implementation of time redundancy of frames in order to tolerate temporary faults in the channel and, therefore, increase the reliability of the network.

1 August 2014 in IET Power Electronics
Verified
Journal Article
Open access
PDF file
ZIZeljko Ivanovic
Zeljko Ivanovic
BBBranko Blanusa
Branko Blanusa
MKMladen Knezic
Mladen Knezic
An analytical power losses model of boost rectifier is presented in this study. A power losses model that takes into account both continuous and discontinuous current modes is derived. The analytical expressions of conduction and dynamic losses, including losses in inductor core and winding, are given. Also, equivalent input resistance, which models single‐phase and three‐phase rectifiers’ power losses, is modelled. The model is verified through simulations and experimental measurements on single‐phase boost rectifier that is used in wind turbine with permanent‐magnet generator.

1 September 2010
Verified
Conference Paper
Closed access
MKMladen Knezic
Mladen Knezic
BDBranko Dokic
Branko Dokic
ZIZeljko Ivanovic
Zeljko Ivanovic
Fieldbus networks based on Ethernet become an inevitable part of factory automation systems. The number of installed nodes has increased over the last few years. Therefore, efficient network planning sets new challenges for today's engineers. This paper shows major aspects of topology planning in industrial networks based on EtherCAT protocol.

1 September 2011
Verified
Conference Paper
Closed access
MKMladen Knezic
Mladen Knezic
BDBranko Dokic
Branko Dokic
ZIZeljko Ivanovic
Zeljko Ivanovic
EtherCAT protocol is a popular Real-Time Ethernet solution that offers the highest communication efficiency in a number of operating conditions. However, for huge networks with several hundreds of devices distributed in the field, EtherCAT performance can become a critical factor. In this paper, we propose a solution for increasing EtherCAT performance using a frame size optimization algorithm. The optimization algorithm is described and analyzed for a simple scenario present in typical automation systems.

1 September 2010
Verified
Conference Paper
Closed access
ZIZeljko Ivanovic
Zeljko Ivanovic
BDBranko Dokic
Branko Dokic
BBBranko Blanusa
Branko Blanusa
MKMladen Knezic
Mladen Knezic
A method for efficiency optimization of boost converter applied in wind turbine with permanent magnet generator (PMG) is proposed in this paper. This method gives the best results when output power of generator is less than rated value. Its validation is verified through simulation and experimental results.