12 October 2020 in Biomass Conversion and Biorefinery
30 January 2018 in Journal of Polytechnic
One of the major pollutants in water resources are organic dyes that are widely used by different industries. Methylene blue (MB) is one of them which is quite harmful for aquatic life. This pollutant must be removed with proper methods. Adsorption is one of the most popular methods because of its high purification yield and known as a cost effective process if the sorbent is inexpensive. In this study, biochar which is used as an adsorbent has been produced from hazelnut shells used as the raw material. Chemical, thermal and surface characteristics of raw hazelnut shell were investigated by FT-IR, TG/DTG, SEM and elemental analysis. Biochar characteristics were determined by FT-IR, BET and SEM analysis. The effect of different adsorption parameters such as pH, initial dye concentration, contact time, adsorbent dosage and temperature on the adsorption of MB onto hazelnut shell char were examined in batch experiments. The equilibrium of adsorption was modeled using Langmuir and Freundlich isotherm models. The maximum adsorption yield of MB was found to be 83% at pH 4.0, adsorbent dosage of 4 g/L, contact time of 300 min., initial dye concentration of 15 mg/L and temperature of 45 o C. In addition, the Freundlich isotherm was found to be the best fitting isotherm model for the adsorption process. The pseudo-first-order and pseudo-second-order kinetic models were applied to the experimental data and thermodynamic parameters such as Gibbs free energy, enthalpy and entropy were determined.
28 April 2020 in Fullerenes, Nanotubes and Carbon Nanostructures
In this study, hazelnut shell and walnut shell which are the agricultural wastes existent abundantly in many countries were pyrolyzed at different temperatures in the temperature range of 400–700 °C in order to optimize the physicochemical properties of biochars. The biochars with large surface area were used to removal of lead (Pb2+) ions, one of the most important heavy metal pollutant, from aqueous solutions. The characterization of raw biomass and also biochars produced by pyrolysis were performed using FT-IR, BET, SEM, partial and elemental analysis techniques. In order to determine the adsorption characteristics of both biochars, batch adsorption experiments were carried out under different experimental conditions. The optimum conditions were determined by investigating the effect of adsorption parameters (initial heavy metal concentration, temperature, adsorbent amount, pH, contact time and mixing speed) for efficient removal of Pb2+ ions from aqueous solution. The experimental results were investigated in terms of Langmuir, Freundlich and Temkin isotherm models. Together with the calculated thermodynamic parameters, the adsorption mechanism was tried to be explained. In order to determine the kinetic model of the adsorption process, the experimental data were applied to pseudo first-order, pseudo second-order and intra-particle diffusion model, and the model constants were investigated.
4 September 2021 in Biomass Conversion and Biorefinery
15 March 2020 in Water Science & Technology
The increasing use of dyestuff in industrial applications brings with it environmental problems. These dyes, which are an eco-toxic hazard, are common water pollutants, even at very low concentrations in water resources. Therefore, they must be removed in an economical way. In this study, low-cost biosorbents such as pine cone char, walnut shell char, and hazelnut shell char were prepared by pyrolysis process at different carbonization temperatures in the range of 400–700 °C. Biochars with the highest surface area were used to remove alizarin yellow GG from aqueous solution and the adsorption capacities of these materials were compared to commercially available activated carbon. Biomasses and prepared biochars were characterized using Fourier transform infrared spectroscopy, thermogravimetric/differential thermogravimetry analysis, Brunauer–Emmett–Teller (BET), scanning electron microscopy/energy dispersive X-ray spectroscopy, partial and elemental analysis techniques. Operational parameters such as contact time, temperature, pH, adsorbent dosage, and initial dye concentration were considered as variables for the batch adsorption experiments. Among the biochars used, the highest adsorption efficiency (82%) was obtained in pine cone char (BET surface area 259.74 m2/g) at pH = 3, T = 45 °C, adsorbent dosage of 8 g/L, and initial dye concentration of 20 ppm. The adsorption mechanism has been investigated by applying different kinetic and isotherm models with the aid of time-dependent adsorption data. The adsorption process was best described by Langmuir isotherm and pseudo-second order kinetic model.
29 February 2024 in Biomass Conversion and Biorefinery
This study was carried out to evaluate the potential application of pine cone (PC)-derived activated biochar which has a surface area of 1714.5 m2/g for bromocresol green (BCG) dye removal from aqueous solution. Batch adsorption experiments involved varying pH, temperature, contact time, adsorbent dosage, and initial dye concentrations and the maximum BCG removal (96.27%) occurred at pH: 2.0, T: 45 °C, m: 2 g/L, t: 15 min., and Co: 25 mg/L. To study the characteristics of adsorption, the adsorption kinetic isotherm and thermodynamic parameters were employed. The experimental data was evaluated to fit well with the Temkin isotherm (R2 = 0.99) and the adsorption process followed pseudo-first-order kinetics (R2 = 0.96). Thermodynamic parameters obtained from the adsorptive uptake showed that the interaction was endothermic and spontaneous in nature. The regenerated activated PC biochar showed good performance (95.0%), even, after 4th regeneration. To predict the BCG adsorption capacity of activated PC biochar, many different artificial neural network (ANN) models have been developed. The optimal ANN model gave mean absolute error (MAE), mean bias error (MBE), root mean square error (RMSE), and R2 values of 0.036, 0.578, 0.947, and 0.999, respectively. The results obtained showed that ANN can be used to effectively model the BCG adsorption process.