28 April 2025 in IEEE Transactions on Plasma Science
The armature–rail interface of the electromagnetic launchers conducts the current with megamperes in the milliseconds. This extreme condition results in the rapid melting of the metal at the armature–rail interface, followed by the outward ejection of molten metal. The molten metal with high-velocity and high-temperature impacts rails and insulators, causing serious grooving damage and metal pollution, which limits the performance and service life of the launcher. To study this phenomenon, a 3-D electro-magnetic-thermal-mechanical-fluid multiphysics coupling model was established, taking into account dynamic contact resistance, velocity skin effect, development trend of the liquefied layer, and fluid pressure. The calculation results show that the liquefied layer initially appears at edges of the front of the armature. And rapidly expands toward the center of the tail. The maximum liquid pressure occurs neartheinterface between solid and liquid. Due to the degradation of the armature material properties caused by high temperatures, high fluid pressure facilitates the peeling of solid part of the armature, thereby accelerating the expansion of the eroded region. At 2.5 ms, the armature melts a volume of 11.91mm3, with a maximum melting depth of 0.565 mm occurring in the edge region of the armature. Meanwhile, the maximum velocity of the liquefied layer reaches 450 m/s.
18 August 2025 in IEEE Transactions on Plasma Science
Deposition occurs on the rail surface during the start-up stage of the launching process. These phenomenon influence the velocity of the armature, the acceleration of the armature and the launching stability of the launcher. In this article, 15 experiments with the linear current density of 19 kA/mm were carried out. The morphology of the rail surface at the armature start-up stage and the start-up time of the armature were measured by a 3-D laser profilometer and a high-speed camera, respectively. Three conclusions are obtained: 1) the morphology of the deposition layer on the surface of rails is high at the edges of armature-rail interface and low in the middle of interface because of nonuniform contact pressure and temperature; 2) as the number of experiments increases, the thickness of the deposition layer on the rail surface increases and then tends to stabilize; and 3) the start-up time of the armature increases rapidly, and then tends to stabilize. Moreover, to analyze the reason for the distribution of deposition layer on the rail surface observed during start-up stage in experiments, the contact pressure, current density and Joule heating were calculated. Results show that the contact pressure of the edges of the armature is relatively high, and these areas are also where high temperature is concentrated on the surface of the armature.
21 March 2025 in IEEE Transactions on Plasma Science
The contamination degree, which is used to evaluate the degradation of insulation performance in solid-armature rail launchers, is proposed based on the study of pollution flashover in power systems. Two methods for describing the contamination degree, namely the leakage current method and the partial surface conductivity method, are introduced based on the contamination characteristics of bore insulators. The correlation between two descriptive parameters, the leakage current ${I} _{\text {leak}}$ and the partial surface conductivity $\sigma _{p}$ , and flashover voltage ${U} _{f}$ was investigated under various sample sizes and experimental conditions. Results indicate that the partial surface conductivity method, in general, is more suitable for describing the contamination degree of bore insulators. In cases where faults or severe contamination occur on insulators, the flashover voltage ${U} _{\boldsymbol {\sigma }}$ predicted by $\sigma _{\!p}$ is closer to the measured value ${U} _{f}$ than the ${U} _{I}$ predicted by ${I} _{\text {leak}}$ , with ${U} _{I}$ typically being higher than ${U} _{f}$ . For a large sample size of 288 samples, the correlation coefficient between $\sigma _{p}$ and ${U} _{f}$ was found to be −0.89. The relationship between $\sigma _{p}$ and ${U} _{f}$ follows a power function, and the regression fitting yielded the equation ${y} = 0.853~{x} ^{-0.1}$ . The establishment of the contamination degree and the application of descriptive methods provide valuable insights into the damage distribution and degradation mechanisms of bore insulators.
1 November 2026 in IEEE Transactions on Plasma Science