Yoichiro Sato

Yoichiro Sato

Auto-generated profile, based on publicly available information

Yoichiro Sato

Nagoya University, Nagoya, 464-8603, Japan

Research Focus & Metrics

Academic Career Length

28Years (1999-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2015
Verified
Conference Paper
Closed access
SMScott R. McCann
Scott R. McCann
YSYoichiro Sato
Yoichiro Sato
VSVenkatesh Sundaram
Venkatesh Sundaram
RTRao R. Tummala
Rao R. Tummala
SSSuresh K. Sitaraman
Suresh K. Sitaraman
Glass interposers have gained increased attention and interest in microelectronics industry since 2010. This is because glass has a tailorable coefficient of thermal expansion (CTE), high mechanical rigidity, availability in large and thin panel form, low processing cost, smooth surface for fine line and space fabrication, and superior electrical properties. While thin glass panels offer such a plethora of benefits, there are several processing and reliability challenges that glass imposes. As a brittle material, glass has low fracture toughness and is prone to cracking. In a typical large-area glass panel processing, layers of dielectric polymers and conducting copper are sequentially deposited and patterned. Due to these temperature histories and difference in the CTE among different materials, the panel is subjected to process-induced residual stresses. When the panel is subsequently diced into smaller substrates, the glass could crack. This cracking is due to high residual stresses as well as dicing defects and possible delamination at the polymer-glass interface. This experimental and theoretical work aims to investigate thin glass cracking and understand the mechanics of such cracks, focusing on the stresses induced by build-up layers. As part of this work, glass panels of 150 x 150 mm size and 100 μm thickness were laminated on both sides with ZS-100 polymer of 10 - 22.5 μm thickness and cured. After the lamination process, 5 - 10 μm thickness of copper is then deposited through a semi-additive electroless and electrolytic plating processes. This process of polymer and copper are repeated to create a total of two metal layers on each side of the panel. The panel is then diced into 18.4 x 18.4 mm substrate coupons. Dicing defects are characterized using optical inspection. Cracking failures are documented. The unbroken substrates are thermal cycled between -40 and 125 °C. In parallel to the experimental investigation, numerical models are created based on the sequential fabrication process. Copper material properties are obtained from literature as well as from in-house nanoindentation tests. Polymer properties are obtained from vendor data, and the stress-free temperature is obtained through experiments. Dicing process is simulated by inserting a vertical crack through the panel, and various dicing defects are introduced in the singulated substrate. Energy available for crack propagation of such defects is determined through fracture mechanics approach, and design guidelines to mitigate glass fracture during dicing and reliability testing are explored.

20 April 2019 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
YSYoichiro Sato
Yoichiro Sato
NINobuhiko Imajyo
Nobuhiko Imajyo
KIKenji Ishikawa
Kenji Ishikawa
RTRao Tummala
Rao Tummala
MHMasaru Hori
Masaru Hori

1 May 2013
Verified
Conference Paper
Closed access
YSYoichiro Sato
Yoichiro Sato
SSSrikrishna Sitaraman
Srikrishna Sitaraman
VSVijay Sukumaran
Vijay Sukumaran
BCBruce Chou
Bruce Chou
JMJun-Ki Min
Jun-Ki Min
RTRao Tummala
Rao Tummala
This paper demonstrates ultra-miniaturized RF passive components integrated on thin glass substrate with small Through Package Vias (TPVs) to realize 3D Integrated Passive and Actives Component (IPAC) concept. Miniaturization is achieved through; a) ultra-thin glass, b) low-loss thin dielectrics and c) small TPVs. Inductors, capacitors and low pass filters functioning in the frequency range of 0.8 GHz to 5.4 GHz were modeled and fabricated between thin dielectric layers on 100 μm thin glass, and then assembled on PCB through BGA interconnections. The simulated results corroborated well with measured results, providing guidelines for RF module fabrication.

1 May 2019
Verified
Conference Paper
Closed access
KHKazutaka Hayashi
Kazutaka Hayashi
NKNobutaka Kidera
Nobutaka Kidera
YSYoichiro Sato
Yoichiro Sato
In this paper, we will introduce the dielectric characteristics of newly developed glasses and discuss the effect of electrical properties of the glasses on the characteristics of glass-employed devices through numerical simulation.

1 February 1999 in Journal of the American Ceramic Society
Verified
Journal Article
Closed access
PDF file
XFXiaobao Fan
Xiaobao Fan
TITakamasa Ishigaki
Takamasa Ishigaki
YSYoichiro Sato
Yoichiro Sato

31 July 2020 in Journal of Physics D: Applied Physics
Verified
Journal Article
Closed access
PDF file
YSYoichiro Sato
Yoichiro Sato
KKKaede Katsuno
Kaede Katsuno
HOHidefumi Odaka
Hidefumi Odaka
NINobuhiko Imajyo
Nobuhiko Imajyo
KIKenji Ishikawa
Kenji Ishikawa
Masaru  HoriMasaru Hori
Masaru Hori
The concept of using a glass substrate with fine through-holes filled with metal, called through-glass-vias (TGVs), for an inner wall of an enclosure of a nonequilibrium atmospheric pressure plasma source was validated to extend its processing area with high plasma densities maintained. When applying the TGV substrate into an inner wall of the plasma source, the generated discharge was less likely to drift along with the gas flow, which resembled the behavior of locally high electric fields of the plasma source, called the creeping mode. The decrease in breakdown voltage was also observed. These phenomena are caused by the TGV areas acting as a steering control material in the enclosure of the plasma source. The location of the TGV areas affected the behavior of the generated plasma. The shape of the plasma was accomplished to arbitrarily and locally control by the placement of TGVs.