Experimental studies of high-velocity (1-4 km/s) impacts of laser-launched flyer plates with polycrystalline, glassy or polymer windows were performed, with the intent of understanding and assessing the use of optical windows as high-speed solid-state shock wave detector materials. The problem is that the detector material undergoes radical physical transformations during the measurement. Here we present a simplified model where the detector material transformations are described as velocity and time dependent changes in shock impedance. The window materials were used to study the detonation shock produced by nitromethane, which is about 20 GPa and 10 ns. Reference experiments producing shocks in this pressure and duration range characterized how the shock impedances changed with impact velocity and shock duration. Sapphire, CaF2 and LiF windows had the fastest response to the detonation shocks, while the polymer windows had a sluggish response. Pyrex and BK7 were the best of the glassy windows.
TATB (1,3,5-triamino-2,4,6-trinitrobenzene) is a powerful explosive whose dynamical behavior is difficult to study because TATB is so insensitive to initiation by shock waves. We used a tabletop microscope equipped with 0–4.5 km/s laser-launched flyer plates to study shock initiation of TATB, which was fabricated in the form of an array of hundreds of plastic-bonded explosive minicharges (X-TATB = 80% TATB + 20% Sylgard 182 polymer). The 4 ns shocks from the flyer plates were not effective in initiating TATB, but we also developed a two-layer array where flyers first initiated a plastic-bonded PETN (pentaerythritol tetranitrate) charge (X-PETN = 80% PETN + 20% Sylgard), which drove an initiating 25 ns shock into the X-TATB. Thermal emission from shocked X-TATB was used to measure time-dependent temperature profiles with a resolution of 2 ns and to produce high-speed (5 ns) videos. In X-TATB, flyer plates produced 2500–3500 K hot spots and combustion at 2500 K. With X-PETN initiators, X-TATB had 3500–4000 K hot spots and a powerful volume explosion lasting a few nanoseconds. Prospects for producing TATB detonations on a tabletop are discussed.
The aggregate behavior of hot spots in shocked plastic-bonded explosives (PBX) was studied by nanosecond optical pyrometry. The averaged thermal emission spectra from at least 25 tiny (50 μg) explosive charges of a pentaerythritol tetranitrate PBX, at several impact velocities from 1.5 to 4.5 km/s, was used to determine average temperatures and emissivities. Individual spectra were analyzed to determine the distribution of hot spot temperatures in individual charges with unique microstructures. Understanding shocks in tiny charges with different microstructures is needed to understand shocks in large PBX charges which sample many microstructures as they propagate. The initial hot spot density was several percent, and the average initial hot spot temperature of 4000 K was, surprisingly, independent of impact velocity. With underdriven shocks, the initial hot spot temperatures clustered around 4000 K, but with overdriven shocks, there were both hotter and colder hot spots. The initial hot spot density increased quadratically with impact velocity. The generation of hot spots was described by a model with a threshold energy to trigger hot spot formation and a distribution of energetic barriers to hot spot formation.
TATB (1,3,5-triamino-2,4,6-trinitrobenzene) plastic-bonded explosives (PBX) were shocked with laser-launched flyer plates. The spectral radiance of the emitted light from a small portion of the microstructure (a “microenvironment”) containing a small number of TATB particles with an estimated mass of 150 ng was measured every 0.8 ns from 1 ns to 200 μs and was analyzed to give radiance and time-dependent graybody temperatures. By fabricating an array with 186 PBX charges, we could obtain ≥15 shots at each of 12 velocities between 1.8 and 4.7 km/s. We found that every microenvironment generated a unique radiance fingerprint. Some of these microenvironments were much more reactive than average. The radiance has two peaks around 20 ns and 5 μs, associated with shock ignition and deflagration growth. In our interpretation, the shock creates an ensemble of hot spots of various sizes and temperatures. Of those hot spots that ignite, only a small portion, at about 2200 K, was large enough and hot enough to survive long enough (>100 ns) to ignite individual TATB particles, leading to deflagration. Integrating various time intervals of the radiance can quantify the strength of the shock–PBX interaction, and the decay and growth of the hot spot ensemble and the deflagration.
8 December 2022 in The Journal of Chemical Physics
In operando studies of high explosives involve dynamic extreme conditions produced as a shock wave travels through the explosive to produce a detonation. Here, we describe a method to safely produce detonations and dynamic extreme conditions in high explosives and in inert solids and liquids on a tabletop in a high-throughput format. This method uses a shock compression microscope, a microscope with a pulsed laser that can launch a hypervelocity flyer plate along with a velocimeter, an optical pyrometer, and a nanosecond camera that together can measure pressures, densities, and temperatures with high time and space resolution (2 ns and 2 µm). We discuss how a detonation builds up in liquid nitromethane and show that we can produce and study detonations in sample volumes close to the theoretical minimum. We then discuss how a detonation builds up from a shock in a plastic-bonded explosive (PBX) based on HMX (1,3,5,7-Tetranitro-1,3,5,7-tetrazocane), where the initial steps are hotspot formation and deflagration growth in the shocked microstructure. A method is demonstrated where we can measure thermal emission from high-temperature reactions in every HMX crystal in the PBX, with the intent of determining which configurations produce the critical hot spots that grow and ignite the entire PBX.