19 August 2020 in IEEE Transactions on Antennas and Propagation
A wideband high-power dual-branch helical reflectarray antenna (RAA) is presented. The reflecting element consists of two metal helical branches, and the variable rotation angles enable full 360° phase adjustment. An X-band RAA prototype with 9 × 9 rectangular grid is simulated and measured. Full-wave simulations show that the maximum gain of 23.7 dB is achieved with the beam focused at (θ=20°, φ=0°) direction at center frequency of 9.3 GHz and the 1-dB gain bandwidth is over 24.2%. The measured reflection coefficient is lower than -16.3 dB in the whole band. From 8.4 GHz to 10.8 GHz, the tested axial ratio is less than 2.3 dB. At center frequency, the tested gain is 23.4 dB and the corresponding aperture efficiency is 50.6%. The beam-scanning performance of the RAA is tested within 30° angular in two orthogonal planes with the scan loss of less than 1.5 dB and the axial ratios of lower than 1.4 dB. Taking the flat-topped beam as an example, the beam-forming capability of the RAA is verified. The measured results demonstrate the feasibility of the proposed design. The simulated results show that the power-handling capacity of the RAA is about 358 MW under vacuum condition.
23 January 2018 in IEEE Antennas and Wireless Propagation Letters
A novel high-power axial-mode helical antenna has been developed. The antenna consists of two short helixes with the same polarization but a relative rotation angle. As the high-frequency current on the antenna is divided into two paths, its power capacity is much higher than conventional helical antenna. Some basic analysis and design of the dual-branch helical antenna are presented and a wideband, well-matched coaxial feeding for experiments has been carried out to get the frequency responses and far-field results. The results centered at 12.5 GHz indicate that the gain is 8.6 dB and the axial ratio is 2.2 dB, and it could handle a pulse power of 44.6 MW under vacuum condition.
7 November 2017 in IEEE Microwave and Wireless Components Letters
A novel high-power orthogonal over-mode circular waveguide (CWG) TE11-TM01 mode converter is presented. This mode converter is made up by two orthogonal CWGs and two metal plates. One metal plate is used to achieve phase shift of two semicircular waveguide TE11 modes. In the bend, phase difference between the two TE11 modes is changed from $\pi $ to $2\pi $ , which meets the requirement of mode conversion at the end of the metal plate. The other metal plate is used to reflect and suppress CWG TE21 mode, and thus power-handling capacity is greatly improved because lager radius of CWG can be utilized. After optimizing basic parameters, simulation results show that the mode converter has virtues of high power-handling capacity, high conversion efficiency, and a very small bend radius. Finally, test result of the VSWR has a good agreement with simulation result and insertion loss is 0.12 dB at 8.4 GHz. All of that prove the feasibility of the mode converter.
24 June 2022 in IEEE Transactions on Antennas and Propagation
A compact dual-wideband millimeter-wave magnetoelectric (ME) dipole antenna based on dual-mode operation is proposed in this article. The ME dipole consists of two mirrored U-shaped patches, a substrate integrated waveguide (SIW) cavity with slotted top and two metallized vias connecting the patches to the slot. The two mirrored U-shaped patches work as an electric dipole (E-dipole), while the slot on the top of the SIW cavity and two metallized vias work as a magnetic dipole (M-dipole). In the lower frequency band, 0.5 λ modes of the E-dipole and the M-dipole are excited to form the 0.5λ mode of the ME dipole. In the higher frequency band, 1 λ modes of the E-dipole and the M-dipole are excited to form the 1λ mode of the ME dipole. In order to achieve compact structure and wide bandwidths, an SIW cavity is designed to feed the antenna. The propose design shows that the measured impedance bandwidths (return loss larger than 10dB) are 24-29.3GHz and 35.5-43.5GHz at least with the achieved gain of 4.8-6.1dBi and 6.8-8.7dBi. The designed antenna is suitable for 5G dual-band millimeter-wave applications.
25 May 2018 in IEEE Transactions on Antennas and Propagation
A 28-element radial-line helical subarray at Ku-band is designed. In order to realize high power capacity at high frequency, we present a new form of helical antenna, especially, for array applications, it has high power capacity and little mutual coupling. On the other hand, since there is inhomogeneous energy distribution inside the radial-line, an improved probe is used to help control the feed coupling, this probe has the advantages of simple structure, high coupling coefficient, and easy fabrication, which are suitable for high-frequency applications. The designs of the components are discussed in detail and the power capacity of the subarray is obtained by simulation. Compared with the typical radial-line helical arrays, the proposed subarray has not only higher power capacity but also fewer elements. Experimentally, the low-power results of an array prototype combined by four subarrays indicate that high gain as well as circular polarization has been successfully verified. From the high-power test, the array is powered by tens of megawatts of pulsed power that extracted from a transit-time oscillator. As expected, the power handling capacity of the combined array is found to be 75 MW in SF6 gas condition.
17 May 2021 in IEEE Access
The demand for multi-band high-power antennas, which have been rarely reported, becomes urgent in high-power microwave field. To meet the demand, a C/X dual-band high-power circularly polarized patch reflectarray antenna is proposed in this paper. Two main technologies are adopted to make the proposed antenna realize the high-power feature. Firstly, the elliptical patch with no abrupt structure is proposed to be the dual-band reflecting element to mitigate the electric field concentration. Secondly, the elliptical patches are proposed to be embedded into substrate to avoid the triple junction. The proposed dual-band reflecting element is designed by arranging two embedded elliptical patches with different sizes in a square lattice grid. The larger elliptical patch operates in C-band and the smaller one works in X-band. The elliptical patches are proposed to be rotated to realize continuous 360 ° phase response in both bands. By optimizing the thickness of substrate, the element spacing, and the size of the patches, the dual-band element shows good reflection amplitude and phase response and low mutual coupling performance. An antenna prototype with the aperture size of 345 mm ×345 mm is simulated and measured. The measured radiation results of the designed reflectarray antenna are in good agreement with simulations in both C-band and X-band. The measured gain of the antenna at 6.2 GHz is 24.6 dBi, and at 9.3 GHz is 27.8 dBi. Full-wave simulations show that the power capacity of the antenna at 6.2 GHz is about 10.2 MW, and at 9.3 GHz is about 3.9 MW in air condition. The low mutual coupling performance of the proposed antenna is verified both in element level and array level. All of the results show that the proposed antenna has the merits of high-power capacity, dual-band, and low mutual coupling.