Multiple energy extraction (MEE) is a technology that was recently introduced by Hitachi for its spot-scanning proton treatment system, which allows multiple energies to be delivered in a single synchrotron spill. The purpose of this paper is to investigate how much beam delivery time (BDT) can be reduced with MEE compared with single energy extraction (SEE), in which one energy is delivered per spill. A recently developed model based on BDT measurements of our synchrotron's delivery performance was used to compute BDT. The total BDT for 2694 beam deliveries in a cohort of 79 patients treated at our institution was computed in both SEE and 9 MEE configurations to determine BDT reduction. The cohort BDT reduction was also calculated for hypothetical accelerators with increased deliverable charge and compared with the results of our current delivery system. A vendor-provided MEE configuration with 4 energy layers per spill reduced the total BDT on average by 35% (41 seconds) compared with SEE, with up to 65% BDT reduction for individual fields. Adding an MEE layer reduced the total BDT by <1% of SEE BDT. However, improving charge recapture efficiency increased BDT savings by up to 42% of SEE BDT. The MEE delivery technique reduced the total BDT by 35%. Increasing the charge per spill and charge recapture efficiency is necessary to further reduce BDT and thereby take full advantage of our MEE system's potential to improve treatment delivery efficiency and operational throughput.
We study a class of supersymmetric models with nonuniversal gaugino masses that could arise from -terms in a general combination of the singlet and adjoint representations of . We explore models that satisfy present Large Hadron Collider and other bounds, showing how the allowed parameter space is divided into distinct “continents.” Regions of parameter space that ameliorate the supersymmetric little hierarchy problem with a small parameter include the usual focus-point scenario, but also natural areas with much lighter squarks and sleptons. These models are continuously connected in parameter space to regions in which stau coannihilation or Higgs exchange is mostly responsible for dark matter annihilation, and to models in which the thermal relic abundance is achieved by slepton-mediated annihilation, reviving the bulk region that is severely restricted in minimal supergravity models. In hybrid or confluence regions, several mechanisms combine to give the requisite dark matter annihilation rate. In each case, we study the prospects for direct detection of dark matter. We also comment briefly on the impact of recent hints for near 125 GeV from the LHC.
If the lighter top squark has no kinematically allowed two-body decays that conserve flavor, then it will live long enough to form hadronic bound states. The observation of the diphoton decays of stoponium could then provide a uniquely precise measurement of the top squark mass. In this paper, we calculate the cross section for the production of stoponium in a hadron collider at next-to-leading order (NLO) in QCD. We present numerical results for the cross section for production of stoponium at the LHC and study the dependence on beam energy, stoponium mass, and the renormalization and factorization scale. The cross-section is substantially increased by the NLO corrections, counteracting a corresponding decrease found earlier in the NLO diphoton branching ratio.
The lighter top squark in supersymmetry can live long enough to form hadronic bound states if it has no kinematically allowed two-body decays that conserve flavor. In this case, scalar stoponium may be observable through its diphoton decay mode at the CERN Large Hadron Collider, enabling a uniquely precise measurement of the top-squark mass. The viability of the signal depends crucially on the branching ratio to diphotons. We compute the next-to-leading-order QCD radiative corrections to stoponium annihilation decays to hadrons, photons, and Higgs scalar bosons. We find that the effect of these corrections is to significantly decrease the predicted branching ratio to the important diphoton channel. We also find a greatly improved renormalization-scale dependence of the diphoton branching ratio prediction.
1 January 2019 in Technology in Cancer Research & Treatment
Purpose: To describe and validate the dose calculation algorithm of an independent second-dose check software for spot scanning proton delivery systems with full width at half maximum between 5 and 14 mm and with a negligible spray component. Methods: The analytical dose engine of our independent second-dose check software employs an altered pencil beam algorithm with 3 lateral Gaussian components. It was commissioned using Geant4 and validated by comparison to point dose measurements at several depths within spread-out Bragg peaks of varying ranges, modulations, and field sizes. Water equivalent distance was used to compensate for inhomogeneous geometry. Twelve patients representing different disease sites were selected for validation. Dose calculation results in water were compared to a fast Monte Carlo code and ionization chamber array measurements using dose planes and dose profiles as well as 2-dimensional–3-dimensional and 3-dimensional–3-dimensional γ-index analysis. Results in patient geometry were compared to Monte Carlo simulation using dose–volume histogram indices, 3-dimensional–3-dimensional γ-index analysis, and inpatient dose profiles. Results: Dose engine model parameters were tuned to achieve 1.5% agreement with measured point doses. The in-water γ-index passing rates for the 12 patients using 3%/2 mm criteria were 99.5% ± 0.5% compared to Monte Carlo. The average inpatient γ-index analysis passing rate compared to Monte Carlo was 95.8% ± 2.9%. The average difference in mean dose to the clinical target volume between the dose engine and Monte Carlo was −0.4% ± 1.0%. For a typical plan, dose calculation time was 2 minutes on an inexpensive workstation. Conclusions: Following our commissioning process, the analytical dose engine was validated for all treatment sites except for the lung or for calculating dose–volume histogram indices involving point doses or critical structures immediately distal to target volumes. Monte Carlo simulations are recommended for these scenarios.