Fengchao Wang

Fengchao Wang

Auto-generated profile, based on publicly available information

Fengchao Wang

School of Low-Carbon Energy and Power Engineering, China University of Mining and Technology 4 , Xuzhou, Jiangsu 221116, China

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 March 2024 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
XWXiaojiang Wen
Xiaojiang Wen
LZLingna Zheng
Lingna Zheng
XZXun Zhao
Xun Zhao
YLYingke Liu
Yingke Liu
JKJianhong Kang
Jianhong Kang
MJMingjun Jiang
Mingjun Jiang
Vertical hydraulic transport of particles with wide particle size distributions is a crucial process for coal physical fluidized mining. In the present study, an improved semi-resolved computational fluid dynamics (CFD)-discrete element method was developed to simulate particle flows with wide particle size distributions. In this model, the CFD cells allocated to the particle volume and the momentum source term were defined as the dependent domain and the influential domain, respectively. On this basis, the two-way domain expansion method and the one-way domain expansion method were adopted for the liquid–solid simulation of coarse and fine particles, respectively. The dependent domain expansion coefficient and the influential domain expansion coefficient were proposed to determine the spatial range of the dependent domain and influential domain for the coarse particles, and the optimal modeling strategy for the dependent domain and influential domain expansion coefficient for the coarse particles was determined. Furthermore, a volume expansion method and a momentum source expansion method were proposed for calculating the solid volume fraction of the dependent domain and the source term of the influential domain for the coarse particles. Furthermore, the sample point method was adopted to obtain the solid volume fraction in the dependent domain for the fine particles, and the momentum source term was only updated to the particle-located cell. Subsequently, single-particle settling and binary-particle fluidizing numerical experiments were used to verify the calculation accuracy of the model. The investigation can provide a new method for numerical simulation of liquid–solid flow with wide particle size distributions.

1 September 2024 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
MJMingjun Jiang
Mingjun Jiang
LYLingxiao Yin
Lingxiao Yin
YLYingke Liu
Yingke Liu
BSBiao Sun
Biao Sun
JXJi Xiong
Ji Xiong
LZLiyao Zhang
Liyao Zhang
In the field of deep mining engineering, high-pressure water jets progress toward larger diameters and higher velocities to enhance their impact performance. Understanding the decay characteristics as well as their implications remains challenging. In this article, the jet spread coefficients (k and c) within the empirical model of jet diffusion are determined by series of lab experiments, while simulations using the Eulerian method are conducted by implementing the modified diffusion model as a subroutine. The effects of spread coefficient, jet velocity, and nozzle diameter on the degree of jet decay are studied. The results show that the jet spread coefficient increases logarithmically with increasing jet velocity. With the increase in nozzle diameter, the growth of spread coefficient k of the jet gradually decreases. Increasing the nozzle diameter and spread coefficient k can effectively reduce the decay degree of jet axial velocity and water volume fraction. Notably, although the increase in jet velocity does not impact the decay of axial velocity, it exacerbates the decay of water volume fraction. Similarly, the increase in spread coefficient c has no effect on the reduction of water volume fraction, but it intensifies the decay of jet axial velocity. The combined effects of increased jet velocity and jet spread coefficient weaken the degree of jet decay. The research presents a comprehensive and innovative study of jet diffusion and attenuation phenomena. These insights not only expand the application of jet diffusion models but also provide theoretical support for understanding and optimizing the application of jets.

8 April 2016 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Open access
PDF file
Wei ZhaoWei Zhao
Wei Zhao
CGchuwen guo
chuwen guo
LWLi-Jun Wang
Li-Jun Wang
FWFeng-Chao Wang
Feng-Chao Wang
Abrasive water jet (AWJ) technology have been widely used for machining, while most commercial applications are based on the injection abrasive water jet (injection AWJ) technology. Compared with injection AWJ, abrasive suspension jet (ASJ) has higher energy efficiency. Under the same system pressure, the material removal rate by ASJ is up to five times higher than that by injection AWJ. This paper studied the pressure variation characteristics of ASJ machining system. Two models were built to describe the boosting and decompression processes of ASJ system. The decompression time of ASJ system can be predicted with the model of decompression process. The model of boosting process can be used to predict the target maximum pressure and the time consumption of boosting process, which are two important factors that have significant effects on the machining efficiency. The boosting process of the ASJ system is very important for machining. The influence of the compressibility of water and the friction resistance of the hydraulic system on the pressure variation characteristics of ASJ system during the machining process was also discussed.

28 April 2023 in Research Square
Verified
Preprint
Open access
PDF file
LLLiucan Li
Liucan Li
NXNanzhe Xiao
Nanzhe Xiao
CGChuwen Guo
Chuwen Guo
FWFengchao Wang
Fengchao Wang
Carbon fiber reinforced plastics (CFRP) are widely used in many fields such as aerospace, nuclear reactors, automobiles, ships, and so on, due to their excellent mechanical and thermophysical properties. However, the cutting of CFRP with traditional cutting tools has many problems, such as tool wear, section delamination, large thermal stress zones, and poor surface roughness. As a precision cold cutting technology, abrasive suspension jet (ASJ) can effectively overcome these problems. In this paper, ASJ is used to cut various commonly-used CFRP, and the delamination, surface roughness, average inclination angle, and upper edge collapse of the cutting surfaces are analyzed by ultra-depth-of-field optical microscope. The effects of jet parameters upon the cutting quality of various CFRP are studied. The results demonstrated that an improved machining quality can be obtained for CFRP composites with a resin content of 33%, a carbon fiber content of 175 g/m2, and a ply direction of 0/45/90° or 0/90° by using ASJ with a standoff distance of 1 mm, a jet pressure of 20-30 MPa, and a feed speed of 30 mm/min.

29 August 2022 in Research Square
Verified
Preprint
Open access
PDF file
FWFengchao Wang
Fengchao Wang
XLXinwang Li
Xinwang Li
HXHan Xie
Han Xie
WZWei Zhao
Wei Zhao
Microscale, nanometer to micrometer, is critical to research machining quality of abrasive suspension jet processing (ASJP), in which scale the surface topography of the processing section can be clearly shown and the material removal mechanism can be easily determined. In this paper, an experiment was carried out that three kinds of materials, Ti-6Al-4V (TC4), marble, and glass, cut by abrasive suspension jet (ASJ) and the microscale surface topography captured by an ultra-deep three-dimensional microscope. The experimental results showed that microscale surface topography of the three materials cut by ASJ is different due to their brittleness and toughness. TC4 cutting surface is covered by long and thin scratches with straight down direction, marble cutting surface is covered by pot holes, and glass cutting surface is covered by both of the scratches and pot holes. The scratches are between 40 and 140 microns in length, while the pot holes are between 10 and 40 microns in width. Moreover, forming mechanism of the three materials’ microscale surface topography is also different due to their brittleness and toughness. The scratch on TC4 cutting surface is the plastic damage caused by the abrasive particles, and the pot hole is the brittle fracture caused by the abrasive particles. Intermediate between brittle and plastic materials, glass cut by ASJ with both plastic damage and brittle fracture. The conclusions can provide theory guidance in material precision processing with ASJ.