7 December 2006 in Fuel Cells
31 October 2018 in IEEE Transactions on Nuclear Science
High sampling speed can be achieved using multiple Analog-to-Digital Converters (ADCs) based on the Time-Interleaving A/D Conversion (TIADC) technique. Various types of methods were proposed to correct the mismatch errors among parallel ADC channels in TIADC systems, which would deteriorate the system performance. Traditional correction methods based on digital signal processing have good performance, however often only for input signals limited in a narrow frequency band. In this paper, we present our recent work on design of an 8-Gsps 12-bit TIADC system and implementation of real-time mismatch correction algorithms in FPGA devices, over a broad band of input signal frequencies. Tests were also conducted to evaluate the systems performance, and the results indicate that the Effective Number of Bits (ENOB) is enhanced to be better than 8.5 bits (<800 MHz) and 8 bits from 800 MHz to 1.6 GHz after correction, almost the same with that of the ADC chip employed.
8 September 2020 in IEEE Transactions on Nuclear Science
In the field of nuclear medical imaging, nuclear and particle physics electronics, precise time measurement is an important task. In this paper, we focused on a real-time interpolated timing algorithm based on waveform digitization, which can be integrated in an FPGA device. The basic principle of this algorithm is to calculate the pulse peak and the time point when the pulse crosses the threshold. We analyzed the factors that would influence the time precision, and conducted simulations to estimate the effect. After implementing the algorithm in the FPGA, tests were conducted with the results concording well with the simulation, and a time precision of around 3 ps is successfully achieved for the PMT-like pulse digitized by 800 MSps 12-bit ADC.
1 August 2018 in Review of Scientific Instruments
High-speed high-resolution analog-to-digital conversion is the key part for waveform digitization in physics experiments and many other domains. This paper presents a new fully digital correction of mismatch errors among the channels in Time Interleaved Analog-to-Digital Converter (TIADC) systems. We focus on correction with wide-band input signals, which means that we can correct the mismatch errors for any frequency point in a broad band with only one set of filter coefficients. Studies were also made to show how to apply the correction algorithm beyond the base band, i.e., other Nyquist zones in the under-sampling situation. The structure of the correction algorithm is presented in this paper, as well as simulation results. To evaluate the correction performance, we actually conducted a series of tests with two TIADC systems. The results indicate that the performance of both TIADC systems can be greatly improved by correction, and the effective number of bits is successfully improved to be better than 9.5 bits and 5.5 bits for an input signal up to the bandwidth (−3 dB) range in the 1.6-Gsps 14-bit and the 10-Gsps 8-bit TIADC systems, respectively. Tests were also conducted for input signal frequencies in the second Nyquist zone, which shows that the correction algorithms also work well as expected.
5 July 2021 in IEEE Transactions on Nuclear Science
Shanghai high repetition rate X-ray-free electron laser (XFEL) and extreme light facility (SHINE) has been under construction. It aims at producing X-ray pulses in a photon energy range from 0.4 to 25 keV. To achieve the design goal, SHINE requires precise distribution and synchronization of the clock and timing signals over a long distance of approximately 3.1 km. Based on the standard White Rabbit (WR) protocol, a prototype of a high-precision clock and timing electronics is designed based on a customized clock frequency. Great attention is paid to the design of hardware and field programmable gate array (FPGA) logic to achieve high-precision clock synchronization, fine phase adjustment, and frequency tuning, as well as flexible shaping of timing signals. Test results indicate that the skew jitter of the clock signal is better than 20 ps within the frequency range from around 1 Hz to 1 MHz, and the clock phase delay can be adjusted with a step size of about 500 ps. As for the timing signals, the skew jitter is better than 40 ps rms. Moreover, the temperature drifts of the clock and timing signals are better than 3 ps/°C.