6 January 2026 in Plasma Sources Science and Technology
The article introduces the plasma evolution of dielectric barrier discharge driven by the pulsed waveforms. The model is established under the Afivo adaptive grid framework and PIC-MCC simulation method. Through introducing the heavy particle reaction process, such as ion drift motion, photoemission, the accumulation and mapping of surface charges, and twobody radiative recombination process, the details of the plasma forming process and distribution is discussed. . The study yielded the evolution of electron and ion distributions under a time-varying electric field, corresponding alterations in potential and electric field induced by charged particle motion, are obtained under the first pulse of dielectric barrier discharge (DBD) structure at 2 kPa argon. The simulation results reveal the inceptive discharge evolution at the rising edge of pulse, the discharge extinction occurred near the upper dielectric layer is induced by the reverse electric field formed by the surface charge accumulation at the pulse duration period, and the second plasma packets in the entire cavity is obtained at the falling edge of the pulse. Meanwhile, the time resolved plasma discharge intensity distribution is obtained by ICCD, and the comparison and explanation of the result is discussed with the proposed simulation model. The key factor of formation of plasma sheath at different time period and the verification of simulation result is discussed. The proposed model is of great significance for exploring the evolution of plasma dynamics and the evolution of long pulse width discharges by analyzing the evolution process of discharge points during the first pulse, which is non steady state.
17 May 2019 in Journal of the Society for Information Display
19 December 2013 in Computer Networks
1 November 2019 in Physics of Plasmas
Different spatiotemporal modes of ionization wave propagation at opposite polarity of bipolar pulses in a micro-dielectric barrier discharge structure device are investigated. The device is fabricated on a heavily doped n-type silicon substrate, and a 1 cm × 1 cm square cavity is formed on the 180 μm-thick polyimide film. Different modes of ionization wave propagation determined by the polarity of bipolar pulses are observed, and the details of streamerlike mode and wavelike mode under positive and negative half cycles of pulses are investigated, respectively. The propagation speeds of streamerlike ionization waves and wavelike ionization waves are ∼120 km/s and ∼40 km/s on average and ∼150 km/s and ∼70 km/s in maximum, respectively. Different parameters of bipolar pulses, especially the rising time of pulses, are applied to the proposed device to explore the variation of ionization wave propagation properties. The results show that the modes of the ionization wave propagation are barely changed when the device is driven by different rising time pulses. However, the initial plasma generation time and propagation speed are greatly changed. With a decrease in the rising time from 400 ns to 50 ns, the initial plasma generation time is brought forward over 200 ns, and the ionization wave propagation speed is improved over 30% for both cases. The results imply great significance in the exploration of the dynamics of plasma discharge evolution and regulation of plasma discharge properties through manipulating the pulse parameters.
3 July 2019 in Materials Research Express
27 July 2016 in Journal of Physics D: Applied Physics
A new composite treatment method combining cathode reduction (CR) and electro-pretreatment (EP) is proposed to improve the voltage-controlled negative resistance (VCNR) of porous silicon (PS) emitters. Four groups of PS emitters were treated, with nothing, CR, EP, and a combination of CR and EP, during different preparation stages. The experimental results indicate that both CR and EP improved the VCNR property and the emission characteristics of the PS emitter. The most favorable results occurred for the electron emitter treated with a combination of CR–EP. A peak-to-valley current ratio of 1.06 and an emission current density of 150 µ A cm −2 , which are the lowest value and approximately twice that of other samples, respectively, were obtained. In addition, the operating stability of the PS emitter also improved significantly compared with the two methods alone. Scanning electron microscopy, atomic force microscopy, and energy dispersive x-ray spectrometry results demonstrate that the improvements of the VCNR and the emission characteristics of PS emitters are due to the content variation of defects, impurities, and unstable microstructures in the PS layer under the influence of CR and EP. The mechanism of VCNR behavior is explained by a proposed energy band model, which is consistent with the experimental results.