This paper proposes a design method of the high-speed multi-layer interior permanent magnet synchronous motor (HSML IPMSM) employing the ferrite permanent magnet (PM). Since the maximum speed of the traction motor in this paper is 15 krpm, the mechanical stability must be considered. Additionally, in the case of the HSML IPMSM, as the number of the PM layers increases, the thickness of the PMs must be reduced to be mechanically stable. On the other hand, because the ferrite PM has a relatively low coercive force compared to the Nd PM, an irreversible demagnetization of the ferrite PM of the HSML IPMSM is likely to occur. Therefore, the mechanical stability and irreversible demagnetization must be considered at all design steps. As the irreversible demagnetization and mechanical stability can be confirmed only by finite element analysis (FEA), the proposed method in this paper is a design method that considers the irreversible demagnetization and mechanical characteristics at all design steps using the FEA. After the design of the traction motor is completed using this design method, the designed motor is manufactured. To verify the validity of the design method, experiments are conducted on the manufactured motor, and the test results are compared with FEA results.
20 September 2017 in IEEE Transactions on Energy Conversion
This paper proposes a new numerical formula and a design method to reduce the torque ripple while improving efficiency and the control performance of an interior permanent magnet synchronous motor (IPMSM). In previous studies, the inverse cosine function (ICF) has been used for torque ripple reduction by making the air gap flux density distribution sinusoidal under a no-load condition. However, in this paper, the advanced inverse cosine function (AICF) based on the ICF is proposed. It determines an asymmetric rotor shape for rendering the air gap flux density distribution sinusoidal, considering a certain load condition. In addition to the torque ripple reduction, lower peak values, the total harmonic distortion (THD) of the induced voltage, and a lower iron loss can be achieved by applying the AICF, compared to the other conventional methods. The lower peak value and THD of the induced voltage are important because they affect the control performance of the motor. The lower iron loss can also lead to a higher efficiency, particularly, in the high-speed region. To verify the validity of the proposed design method, the characteristics of 8-pole, 12-slot motors that have different rotor shapes are analyzed using finite element analysis (FEA) and experiments.
2 April 2018 in IEEE Transactions on Industry Applications
In order to improve the performance of the wound field synchronous motor (WFSM), the permanent magnet assist (PM-assist) is investigated in this paper. The effect of the PM-assist is dependent on the inserted position of the PMs. Thus, four models whose PMs are inserted at each different position are suggested. Then, the most effective position of the PM is decided by the mean torque per employed amount of the PM. By inserting the PMs into the decided position of a WFSM designed for a small electric vehicle traction, the PM-assisted WFSM is designed. By comparing the torque and the efficiency of the original WFSM and the PM-assisted WFSM, the effectiveness of the PM-assist is figured out. Finally, the validity of this research is verified by the experiment using the manufactured WFSM.
1 September 2016 in IET Electric Power Applications
The reduction of cogging torque is the most important design objective for electric power steering (EPS) motors, because the rotation characteristics of the motor are directly transmitted to a driver. Therefore, a variety of optimal design methods are applied to reduce the cogging torque for EPS motors. However, the measured cogging torques of fabricated models are significantly greater than the finite‐element analysis (FEA) results, because the additional harmonic components (AHCs) of the cogging torque are generated by manufacturing tolerances. The cogging torque generated by manufacturing tolerances can be divided into two components, which are generated by stator and rotor tolerances. In this study, AHCs, which cause cogging torque, are analysed by FEA by applying various tolerances to the analysis model, and harmonic analysis is also conducted. The relation of AHC generated from the stator and rotor is analysed by a rotor swapping test. Consequently, this study can be helpful to analyse the components of the cogging torque generated by manufacturing processes.
5 September 2017 in IEEE Transactions on Industry Applications
PM-assisted claw-pole synchronous motor (CPSM) has commonly been used in a variety of industrial applications, thanks to its robust structure and high energy density. However, such motor has an axially asymmetric rotor configuration, which induces the corresponding 3-D magnetic field distribution. Thus, this paper proposes an infinitesimal hexahedron-element-based 3-D equivalent magnetic circuit network (EMCN) method in order to estimate the performance of the PM-assisted CPSM. The hexahedron element is considered as an optimum unit element in describing the configuration of the PM-assisted CPSM in detail. That eventually makes it possible to evaluate the specific 3-D magnetic field distribution from which the flux linkage, the back electro-motive force, and the torque are also being calculated. The 3-D EMCN results are compared with 3-D FEA data and/or experimental data to validate their accuracy. Finally, it is proved that the scalar-potential-based 3-D EMCN method requires less computing time than the vector-potential-based 3-D FEA.
3 May 2019 in IEEE Transactions on Vehicular Technology
Hybrid electric vehicles have different performance depending on power distribution and energy management. For heavy-duty vehicles, in particular, these differences will be more pronounced. This paper presents a hybrid powertrain design framework for a heavy-duty multi-purpose vehicle assuming driving conditions. A diesel-powered conventional vehicle was adopted for the hybridization target, and a series hybrid system was suggested as a suitable hybridization topology with an in-wheel motor (IWM) system. The introduced framework supplied the adequate power distribution and the IWM specification based on the speculated drive cycle and a simple energy management strategy. In particular, the reduction ratio of IWM was determined to minimize the gross mass of the motor and reduction gear. The hybridization reduced the vehicle weight by 213 kg while increasing the peak power by 53 kW. Finally, the vehicle simulation was performed using the advanced vehicle simulator for the design result from the proposed framework. The acceleration performance and gradeability limits were improved by 18 % and 10 %p, respectively, compared to the conventional vehicle. In addition, the gasoline equivalent fuel economy of the series hybrid powertrain was 53 % higher than conventional diesel powertrain for the target drive cycle.