Philip Howard Shipway

Philip Howard Shipway

Auto-generated profile, based on publicly available information

Philip Howard Shipway

School of Mechanical, Materials and Manufacturing Engineering, University of Nottingham, University Park, Nottingham NG7 2RD, UK

Research Focus & Metrics

Academic Career Length

36Years (1991-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2007 in Corrosion Science
Verified
Journal Article
Closed access
NHN.C. Hosking
N.C. Hosking
MSM.A. Ström
M.A. Ström
PSP.H. Shipway
P.H. Shipway
CRC.D. Rudd
C.D. Rudd

1 June 2014 in Energy Conversion and Management
Verified
Journal Article
Open access
ARAndrew Roberts
Andrew Roberts
RBRichard Brooks
Richard Brooks
PSPhilip Shipway
Philip Shipway
Legislation on vehicle emissions continues to become more stringent in an effort to minimise the impact of internal combustion engines on the environment. One area of significant concern in this respect is that of the cold-start; the thermal efficiency of the internal combustion engine is significantly lower at cold-start than when the vehicle reaches steady state temperatures owing to sub-optimal lubricant and component temperatures. The drive for thermal efficiency (of both the internal combustion engine and of the vehicle as a whole) has led to a variety of solutions being trialled to assess their merits and effects on other vehicle systems during this warm-up phase (and implemented where appropriate). The approaches have a common theme of attempting to reduce energy losses so that systems and components reach their intended operating temperature range as soon as possible after engine start. In the case of the engine, this is primarily focused on the lubricant system. Lubricant viscosity is highly sensitive to temperature and the increased viscosity at low temperatures results in higher frictional and pumping losses than would be observed at the target operating temperature. The approaches used to tackle the problem include the use of phase change materials (to reduce the cool-down rate during a period following engine running) [1,2] and the use of thermal barrier coatings in an attempt to insulate the cylinder bore and prevent heat loss (thus increasing the amount of energy utilised as brake work [3]). A range of system alterations have also been trialled including diversion systems on the lubricant circuit to reduce thermal losses. Presented here is a critical review of the research into vehicle thermal management during the cold-start phase which has been driven by a desire to improve both engine and overall vehicle engine efficiency. The review includes both system developments and material selection issues and the role the two fields have to play in tackling this critical issue

1 April 1999 in Wear
Verified
Journal Article
Closed access
DSD.A. Stewart
D.A. Stewart
PSP.H. Shipway
P.H. Shipway
DMD.G. McCartney
D.G. McCartney

25 February 2009 in Journal of Thermal Spray Technology
Verified
Journal Article
Closed access
PDF file
THT. Hussain
T. Hussain
DMD. G. McCartney
D. G. McCartney
PSP. H. Shipway
P. H. Shipway
DZD. Zhang
D. Zhang


1 June 2013 in Wear
Verified
Journal Article
Open access
SPS.R. Pearson
S.R. Pearson
PSP.H. Shipway
P.H. Shipway
JAJ.O. Abere
J.O. Abere
RHR.A.A. Hewitt
R.A.A. Hewitt
This paper investigates the effect of temperature (between 24 °C and 450 °C) on the wear rate and friction coefficient of a high strength alloy steel (Super-CMV) in gross sliding fretting in air. It was found that whilst there was significant loss of material from the contact during fretting at room temperature, the overall loss of material from the contact had become negative even with a modest increase in temperature to 85 °C. At temperatures greater than 85 °C, negative wear was maintained, with the coefficient of friction dropping monotonically with increasing temperature up to 450 °C. It is proposed that the changes in wear rate and friction coefficient were due to changes in the way that the oxide particles sintered to form a protective debris bed, with sintering of the oxide debris particles at these low temperatures being promoted by the nano-scale at which the oxide debris is formed