Ying Wang

Ying Wang

Auto-generated profile, based on publicly available information

Ying Wang

Department of Electrical, Computer, and Software Engineering, Ontario Tech University, Oshawa, ON, Canada

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 December 2021 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
OSOlolade M. Sanusi
Ololade M. Sanusi
YWYing Wang
Ying Wang
LRLangis Roy
Langis Roy
A multifunctional reconfigurable metasurface based on liquid metal injection is presented. The reflective flexible material metasurface formed by two switchable microfluidic layers— the top layer comprising an array of meandered half-rings and the lower layer, straight meander lines—can be reconfigured into four states. The proposed metasurface becomes a reflector with emptied channels, whereas it exhibits linear-to-circular polarization conversion (or linear-to-cross-polarization conversion) properties when the top (or bottom) layer is filled with a liquid metal alloy. Upon normal excitation of linearly u/v-polarized waves and activation of the bottom layer, the metasurface reflects cross v/u-polarized waves in the frequencies from 9.83 to 17.42 GHz (53% bandwidth) with a polarization conversion ratio (PCR) of at least 90%. On the other hand, the metasurface operates as a linear-to-circular polarizer (for u/v-polarized waves) over 8.97–11.30 GHz (23% bandwidth), reflecting left- or right-hand circularly polarized waves. To verify the polarization conversion performance, a $25\times 25$ element metasurface array is fabricated and measured. The experimental results confirm the simulation results over the 8–12 GHz test band. The compactness, structural flexibility, and multifunctionality of the proposed metasurface make it a suitable candidate for modern integrated antenna array systems.

1 November 2017 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
MAMona S. Abdallah
Mona S. Abdallah
YWYing Wang
Ying Wang
WAWael M. Abdel-Wahab
Wael M. Abdel-Wahab
SSSafieddin Safavi-Naeini
Safieddin Safavi-Naeini
The modeling, design and optimization of a new substrate integrated waveguide (SIW) middle fed series rectangular dielectric resonator antenna (DRA) array with 45° linear polarization are presented. The implicit space mapping (ISM) technique is applied for the optimization of the antenna array. A tunable circuit model is built, which serves as the coarse/surrogate mode, and a full wave solver is used as the fine model. High design and optimization efficiency is demonstrated using an eight-element array. The reflection coefficient of the array antenna is optimized with only two iterations. The experimental data for the eight elements antenna array, operating at the millimeter-wave band (34GHz – 36GHz), are used for validation of both performance of the design and modeling techniques. The measured radiation pattern demonstrates a broadside beam with a maximum radiated gain of 13.55 dB over an operating impedance bandwidth of 2.2 GHz.

11 December 2020 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
HXHanyue Xu
Hanyue Xu
YWYing Wang
Ying Wang
FGFarhan A. Ghaffar
Farhan A. Ghaffar
LRLangis Roy
Langis Roy
This article presents novel designs of reconfigurable microwave filters based on the recently introduced concept of field programmable microwave substrate (FPMS). Using reconfigurable FPMS substrate, significant tuning freedom of the designed microwave filters can be achieved. It allows implementation of smart filter designs with tunable center frequencies, operational bandwidths, and filter orders. Moreover, different microwave filter types are also realizable on one FPMS board with simple dynamic control. As a proof-of-concept, design steps are described for three filter types, including waveguide bandpass filter, quarter-wave-coupled bandpass filter, and waveguide bandstop filter. A good match between the simulated and measured results is presented, showing good tuning range for the center frequency and bandwidth of the bandpass filters around 2 GHz. In addition, the reconfigurability of the design allows it to switch to bandstop filters, which is a complete change in topology from a single physical design. The merits of the proposed design are reflected in the realized bandpass filter, exhibiting center frequency tuning of more than 20% along with bandwidth variability spanning three times its minimum value. Finally, a significant size reduction compared with the designs using conventional technologies is also demonstrated. With its inherent flexibility, low cost, and high degree of integration, FPMS filtering is suited to a wide variety of RF applications.

16 April 2019 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
OSOlolade M. Sanusi
Ololade M. Sanusi
FGFarhan A. Ghaffar
Farhan A. Ghaffar
ASAtif Shamim
Atif Shamim
Mohammad VaseemMohammad Vaseem
Mohammad Vaseem
YWYing Wang
Ying Wang
LRLangis Roy
Langis Roy

11 May 2020 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
SCShitao Chen
Shitao Chen
DDDazhi Ding
Dazhi Ding
MYMing Yu
Ming Yu
YWYing Wang
Ying Wang
RCRushan Chen
Rushan Chen
To effectively analyze the electro-thermal characteristics of a semiconductor p-i-n diode in the microwave limiter circuit, a cosimulation algorithm of the time-domain impulse response technique and physical-model-based semiconductor solver is proposed in this article. The physical-model-based semiconductor solver algorithm is based on the drift diffusion model (DDM). First, the multiphysical field coupling equations of the drift diffusion model and heat conduction model are used to analyze the electro-thermal behavior of a semiconductor p-i-n diode. Second, the time-domain impulse response technique based on the field-circuit coupling algorithm is used to extract the time-domain impulse response at each port of the electromagnetic field structure. Finally, the time-domain impulse response is combined with the volt-ampere characteristic relationship of the physical-model-based p-i-n diode. As a result, an efficient computation of the time-domain electro-thermal coupling characteristics of p-i-n diode in the microwave limiter can be obtained. The simulation results are in good agreement with those by the commercial software (COMSOL). The computation time and the memory requirement of the proposed algorithm are significantly reduced when compared with COMSOL.

27 June 2019 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
SLShuQi Li
ShuQi Li
YWYing Wang
Ying Wang
MYMing Yu
Ming Yu
APAntonio Panariello
Antonio Panariello
This paper presents a modeling method for high power dielectric resonator (DR) filter. An efficient and accurate model for DR filter is developed by preserving only the necessary information of the generalized scattering matrix (GSM) for each junction of the filter structure. Doing so, the sizes of the GSMs are dramatically reduced for the training and testing of the neural network (NN) models of each critical junction of the DR filter. The neural models are subsequently connected using a transmission line model for each mode in a cylindrical dielectric rod with conductor housing. Calculations of the propagation constant for each mode are given. The final model contains NN and transmission line models and is thus very fast. The method is described in details using a Ku-band high power DR filter. Efficiency and accuracy of the model are demonstrated through comparison with full-wave simulations and measurements. Excellent agreements are observed for both near-band and wide-band results.