The presence of noise in towed marine seismic data is a long-standing problem. The various types of noise present in marine seismic records are never truly random. Instead, seismic noise is more complex and often challenging to attenuate in seismic data processing. Therefore, we have examined a wide range of real data examples contaminated by different types of noise including swell noise, seismic interference noise, strumming noise, passing vessel noise, vertical particle velocity noise, streamer hit and fishing gear noise, snapping shrimp noise, spike-like noise, cross-feed noise, and streamer-mounted device noise. The noise examples investigated focus only on data acquired with analog group forming. Each noise type is classified based on its origin, coherency, and frequency content. We then determine how the noise component can be effectively attenuated through industry-standard seismic processing techniques. In this tutorial, we avoid presenting the finest details of either the physics of the different types of noise themselves or the noise attenuation algorithms applied. Rather, we focus on presenting the noise problems themselves and find out how well the community is able to address such noise. Our aim is that, based on the provided insights, the geophysical community will be able to gain an appreciation of some of the most common types of noise encountered in marine towed seismic, in the hope to inspire more researchers to focus their attention on noise problems with greater potential industry impact.
Seismic imaging is essential for detailed characterization and understanding of the subsurface. Traditionally, marine seismic data have been acquired either using towed streamers or ocean-bottom receivers. Distributed acoustic sensing (DAS) is a novel and fast-emerging technology that makes it possible to use fiber-optic cables for acoustic measurements. The technology turns the fiber-optic cable into a densely sampled receiver array. A controlled source experiment comparing DAS and conventional towed streamer data for seismic imaging purposes is described. An existing 130 km telecommunication fiber-optic cable was interrogated to acquire DAS data to analyze the signal at long distances and for subsurface imaging. A seismic source vessel was used to create seismic data along the full cable length, while at the same time acquiring conventional towed streamer data for comparison. In addition, the telecommunication fiber-optic cable was used to acquire passive DAS data. The results show that seismic signals in the telecommunication fiber-optic cable are detectable at distances above 100 km from the source point. Furthermore, comparisons of the DAS data and towed streamer data show that the DAS technology allows for the acquisition of large offset seismic data that are comparable with conventional seismic data. Analysis of the passive DAS data shows that the infragravity waves correlate with the observed weather conditions during the acquisition.
Processing marine seismic data is computationally demanding and consists of multiple time-consuming steps. Neural network based processing can, in theory, significantly reduce processing time and has the potential to change the way seismic processing is done. In this paper we are using deep convolutional neural networks (CNNs) to remove seismic interference noise and to deblend seismic data. To train such networks, a significant amount of computational memory is needed since a single shot gather consists of more than 10^6 data samples. Preliminary results are promising both for denoising and deblending. However, we also observed that the results are affected by the signal-to-noise ratio (SnR). Moving to common channel domain is a way of breaking the coherency of the noise while also reducing the input volume size. This makes it easier for the network to distinguish between signal and noise. It also increases the efficiency of the GPU memory usage by enabling better utilization of multi core processing. Deblending in common channel domain with the use of a CNN yields relatively good results and is an improvement compared to shot domain.
The spatial distribution of an air-gun array and the ghost reflection from the air-water interface cause a directional pattern of the source signature and introduce notches at certain frequencies. This significantly limits the bandwidth of the seismic data and the ability to obtain high-resolution subsurface imaging. With mathematical derivation and numerical simulation, we have determined that the inline directivity relies on the number of air guns and their spacing. Furthermore, the effective width of the take-off angles for an air-gun array is highly correlated with the reciprocal of the distance variance along the inline direction, which is subsequently used for optimizing the source design. For a normal horizontal source, one could adjust the distance between two consecutive air guns to improve the source signature. We optimize the spatial distribution for air guns along the inline and depth directions, that is, by using the synchronized multidepth stimulation mode, to minimize the inline directivity. Simulated results show that a six-gun composed multidepth source could be designed to achieve nearly identical energy distribution with up to ±30° take-off angle for the high-frequency end up to 250 Hz. This represents a significant improvement compared to a normal horizontal source and is more suitable for high-resolution seismic acquisition.
The competing effect between the fundamental bubble and its source-ghost response results in a strong attenuation of the lowest frequencies (below 7 Hz). This loss cannot be compensated easily by adjusting the source depth. Consequently, the low-frequency content in marine seismic data is not optimal, degrading the performance of low-frequency dependent processing approaches, such as full-waveform inversion. To overcome this, we have developed an additional source to counteract the ghost from the main source. In this situation, the fundamental bubble is characterized by the depth of the main source, whereas the ghost response is characterized by the summed depth of the main and additional sources. This source setup mitigates the competing effect and reduces the suppression of ultralow frequencies. Compared with a conventional horizontal source, our source design will reduce the mid- to high-frequency output, which may be beneficial in situations in which environmental constraints limit the maximum allowed output of a marine source.